grey with 5speed??

If it doesn't fit below then post here and see if another FB EK fanatic can help you out.

Moderators: reidy, Blacky

fb cruzn
Posts: 294
Joined: Tue Jun 14, 2005 8:52 pm
State: NOT ENTERED
Location: Cowra NSW

grey with 5speed??

Post by fb cruzn »

hey guys, does any one know if its possible to put a supra or celica 5 speed into fb/ek?
has any one on here done it before?
theres plenty of red six toyota conversions around but iv neva seen a grey one?
do or who make the bellhousing?

cheers westy
yeprat1
Posts: 385
Joined: Tue Nov 15, 2005 8:56 pm
State: NOT ENTERED
Location: richmond ;sydney

Post by yeprat1 »

there was a conversion on ebay complete i think it may have been for a grey but it was a nissan five speed $250
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Post by parisian62 »

G'day Westy,

Havnt done it myself but it can be done. Contact Dellow Automotive Pty Ltd Motor Car Accessories 37 Daisy St Revesby 2212 (02) 9774 4419.

also check out http://www.dellowauto.com.au/main.html and look up the product catalogue list - it lists the grey motor.

Have added this contact to the Suppliers and Services list.

Regards
Stewart
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

Castlemain Rod Shop in Victoria may also do a Grey to Celica or Supra 5 speed.Their contact no would probably be locatable online via Yellow Pages.

You would have to fit a larger aftermarket transmission tunnel or an EK Hydramatic tunnel to enable to 5 speed to fit under the floor.

The Datsun/Nissan 5 speeds yeprat1 mentioned were a popular conversion in the '80's and would handle the high power output that a grey puts out :wink: so if you could find a complete conversion for one of these boxes to fit a grey then if its reasonably priced I'd think about one of these.From memory they were a good gearbox and there would still be some around.They did have different length output shafts/housings depending on what model Datsun/Nissan they came from.If you are still using a bench seat you may also have to recess the front seat or modify the gearshift to clear the seat,again this will depend on the output housing length.....shorter is better.

Terry.
I can't think what to write here so this will do.
fb cruzn
Posts: 294
Joined: Tue Jun 14, 2005 8:52 pm
State: NOT ENTERED
Location: Cowra NSW

Post by fb cruzn »

thanx guys, its a ek hydro wagon so room isnt an issue. the one on ebay has been relisted and was to suit red motor :x he failed to mention that bit! ill give dellow a call. ill let ya's know how i go.

westy
mrs ratbox

Post by mrs ratbox »

hey westy where'd you find the wagon
fb cruzn
Posts: 294
Joined: Tue Jun 14, 2005 8:52 pm
State: NOT ENTERED
Location: Cowra NSW

Post by fb cruzn »

hey ratbox, i havnt forgotten bout ya :wink: i found a ek hydro wagon(fair condition stuff all rust) fb ute( all complete but rusted out) fb wagon(minus the roof :shock: ) and 2 fe sedans in a shed, deceaced estate.
got the lot for $200!! got a bit of nasco stuff with them too!
iv only picked up the wagon and the ute but ill let u know when iv got them all if u want. if u still want a body?

westy
mrs ratbox

Post by mrs ratbox »

bastard :lol: where were they. i'm trying to chase up a van at the moment it's in an empty house that's for sale but as yet my phone calls to the R/E have been unanswered
fb cruzn
Posts: 294
Joined: Tue Jun 14, 2005 8:52 pm
State: NOT ENTERED
Location: Cowra NSW

Post by fb cruzn »

its amazing what you can see with binoculars on old dirt back roads :roll:
good luck with the van. theres not many of them round!

westy
smooth

Post by smooth »

I pointed one out local, not sure if Ratbox went and looked at it though?

Regards, Smooth 8)
mrs ratbox

Post by mrs ratbox »

yeah smooth that's the van i'm talking about, don't know about when you saw it but the house is empty now and for sale. and do you think the pricks at the real estate will return my calls :x i have a good mind to just go and tow it away :shock:
smooth

Post by smooth »

ratbox wrote:yeah smooth that's the van i'm talking about, don't know about when you saw it but the house is empty now and for sale. and do you think the pricks at the real estate will return my calls :x i have a good mind to just go and tow it away :shock:
They would probably thank you if you did! It can't add to the rental or sale value. LOL

Can you call on the real estate and pin them to the wall?

Regards, Smooth 8)
mrs ratbox

Post by mrs ratbox »

finally they got back to me, aparently a family member has his eye on it but is just going to let it sit there till the house sells :? must be a deceast estate cause seen photos of the inside of the house and i wouldn't let an animal live in it, actually think the van would be worth more than the house
fb cruzn
Posts: 294
Joined: Tue Jun 14, 2005 8:52 pm
State: NOT ENTERED
Location: Cowra NSW

Post by fb cruzn »

hey guys, strangest thing happend today! i got to work and there was a letter from dellow! i only posted my question on here and hadnt had a chance to call them :shock:
how they knew has got me :shock:
let alone how they got my work address :shock:

but anyway, heres what it says i/you would need.

-bellhousing with side mounts(needed for grey) $325+gst
-pilot bush $25+gst
-steel clutch fork and clip $95+gst
-thrust race and carrier $85+gst
-speedo cable $85+gst
-tailshaft yoke $125+gst
-clutch plate $95+gst

*note-because the car is a auto you also need:-

-master cylinder $100+gst
-slave cylinder $65+gst
-slave cylinder mounting brackets $65+gst
-hydrolic lines and nipples $60+gst
-pedal pushrod $25+gst
-slave to fork push rod $25+gst

i allready have a box and conversion for a red 6 so i prob wont need all this stuff :roll: but it doesnt leave you with much change out of $1300 :shock:
then would still need a tail shaft :shock:

hmmm might have to think about this one :?

westy
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:

Post by parisian62 »

The power of the FB EK Forum in action!

Seriously thats weird...Twilight Zone stuff... :shock:

Thanks for posting up those details.

Regards
Stewart
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Post Reply