Dave’s EK supercharged v6
Re: Dave’s EK supercharged v6
Got some new tooling to help with some fabrication
- Attachments
-
- A8B248D3-F529-4149-A990-18F9E1F204C2.jpeg (2.79 MiB) Viewed 481 times
[*]2 year project currently making its 3rd term
- funkyscooter
- Posts: 557
- Joined: Wed Aug 16, 2017 8:12 am
- State: NSW
- Location: Sydney
Re: Dave’s EK supercharged v6
Look forward to seeing what you make with this!
Scott
(Not so rusty) Ol' Rusty - FB/EK Sedan
(Not so rusty) Ol' Rusty - FB/EK Sedan
Re: Dave’s EK supercharged v6
Just putting some money aside for my shrinker stretcher and I should be right to go
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
Getting ready to high fill the firewall
- Attachments
-
- 037FD924-9CC8-471E-B105-64BEBDD28D6F.jpeg (2.58 MiB) Viewed 439 times
-
- 307DF31D-964D-4027-A2D1-E2746734C26B.jpeg (2.26 MiB) Viewed 439 times
-
- 7EF77383-8B82-4ED0-96F8-D5716560087C.jpeg (2.66 MiB) Viewed 439 times
-
- 8F2A0797-0D84-4420-A2D8-C1D03E94D7D3.jpeg (2.4 MiB) Viewed 439 times
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
I hope it’s warmer in your shed than it is in mine Dave. Shivering in lockdown in SA. Do I recognise Epotec green grey etch prime?
FB ute fixer upper, EK van on rotisserie
FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie
Re: Dave’s EK supercharged v6
Yeh I always spray bare metal in that before anything I do
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
It’s very cold here too but if you close everything up and get working it isn’t too bad. Probably still a lot warmer then where u r haha
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
All in high fill now
- Attachments
-
- 46E4D110-6818-43C2-A98E-3580A09D0409.jpeg (1.33 MiB) Viewed 396 times
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
Here
- Attachments
-
- 88D84C41-4FD2-4348-92E9-3BA6098FAEEB.jpeg (2.57 MiB) Viewed 395 times
-
- B5FE2DB9-7DDA-47EF-8AF8-57634CDC2D31.jpeg (2.71 MiB) Viewed 395 times
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
What are u doing with Pedals Dave. Do u need to swap to a commodore or are you changing boosters. Just looking at the firewall. Nice to see some action.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
FB Ute Stock
EK Ute in Pieces
EK Ute in Pieces
Re: Dave’s EK supercharged v6
Commodore pedals easier to patch everything and drill what is needed and patch once I get to it there was holes everywhere
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
I meant the guy before me butchered the firewall if I weld up most holes and then start again and patch paint as I go.
[*]2 year project currently making its 3rd term
Re: Dave’s EK supercharged v6
Nice Dave. What product and thinner ratio are you using?
FB ute fixer upper, EK van on rotisserie
FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie
Re: Dave’s EK supercharged v6
Using 4:1 but with about 20% thinner
[*]2 year project currently making its 3rd term