Page 1 of 1
Looking for a lower firewall and transmission hump
Posted: Sat Sep 26, 2015 6:59 pm
by rickbantam
Hi to everyone,
I have an EK sedan which someone in the past has removed the standard EK lower firewall (from the seam down to the point where the floor and firewall meets) and transmission hump in preparation for an updated running gear, I would like to have it restored to a grey motor gearbox setup. I am also after a cut of the rear of a sedan mainly the curved section around the fuel filler. If any of you out there in Perth/W.A. have a donor car or know of where I can find one to cut out these sections I would appreciate it, I'm willing to part with cash and/or if anyone is interested in the two spare boot lids I have I can throw those in as bargaining chips.
Thanks for reading and let me know if you can help
Todd
Re: Looking for a lower firewall and transmission hump
Posted: Sat Sep 26, 2015 8:57 pm
by Blacky
Todd, you know where to come
. I have a firewall and a sedan donor you can cut your bits out of
Re: Looking for a lower firewall and transmission hump
Posted: Sat Sep 26, 2015 11:19 pm
by rickbantam
Ha the famous EKmart
Blacky that would be fantastic, let me know when that is convenient for you I appreciate the offer let me know if we can trade parts/cash
Todd
Looking for a lower firewall and transmission hump
Posted: Fri Oct 23, 2015 11:34 pm
by rickbantam
Hey all posted a few weeks ago but I've been all over the country so here goes again I need a donor cut off a lower firewall and tranny hump as you can see by the pic my sedan has been set up for a v8 but I would rather it be stock if any one can help with a donation of this I'd appreciate it. I'm on a tight timeline as I will be moving to Melbourne in mid December for 2 yrs but plan to be back in 2018 with an EK painted with mint body work (my project while I'm there)
you can see in the picture what I'm after from the seam down to where the floor pans go up on the angle and also the tranny hump to where the front seat sits. Drop me a line if you can help I'm willing to pay for the bits
Todd
Re: Looking for a lower firewall and transmission hump
Posted: Sat Oct 24, 2015 9:56 am
by Blacky
its still here Todd......
Re: Looking for a lower firewall and transmission hump
Posted: Sun Oct 25, 2015 10:08 pm
by rickbantam
Blacky
Sorry mate been all over the shop the last couple of weeks and haven't really read the replies - actually I think I'm in WA at the moment Lol, hey if its ok can I come up on Saturday morning (31 Oct) to do some cutting, let me know if thats ok as I'm keen to get this little job done
Todd
Re: Looking for a lower firewall and transmission hump
Posted: Sun Oct 25, 2015 11:01 pm
by Blacky
If I am home , will find out later in the week if I am going bush again on Friday......
Re: Looking for a lower firewall and transmission hump
Posted: Mon Oct 26, 2015 4:33 pm
by rickbantam
Blacky,
No props at all mate I'm free every weekend till mid december so I'll fit in with you
Todd
Re: Looking for a lower firewall and transmission hump
Posted: Thu Nov 05, 2015 12:25 am
by rickbantam
Blacky,
Just let me know a date mate as I'm available most weekends
Todd
Re: Looking for a lower firewall and transmission hump
Posted: Thu Nov 05, 2015 7:32 am
by Blacky
Todd, I SHOULD be flying home tomorrow, I will let you know.
Re: Looking for a lower firewall and transmission hump
Posted: Sat Nov 07, 2015 5:37 pm
by Blacky
Am at home mate.
Re: Looking for a lower firewall and transmission hump
Posted: Mon Nov 09, 2015 11:49 pm
by rickbantam
Blacky
If your up to a visit this weekend let me know have cash and bits to swap and eternal gratitude as well
Todd
you can see in the picture what I'm after from the seam down to where the floor pans go up on the angle and also the tranny hump to where the front seat sits. Drop me a line if you can help I'm willing to pay for the bits