4 speed to auto

Includes clutch, transmission, propeller shaft,
universal joints, differential and rear axle.

Moderators: reidy, Blacky

Post Reply
FantaC
Posts: 58
Joined: Wed Jun 17, 2009 11:26 pm
State: NOT ENTERED

4 speed to auto

Post by FantaC »

Was thinking about putting a trimatic auto into my EH
it has an all Aussie 4 speed at the moment so will the auto fit ?
will i have to change the tail shaft ?
crossmember too ?
im only driving a EH till i get a FB-EK :)
Cheers John
Top
Blacky
Posts: 13404
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Post by Blacky »

Yep , piece a cake mate, just need the right auto (shifter on the right hand side) and its virtually a bolt in job. I have quite a few of the bits you will need - will talk tomorrow.
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

Remember reading a fair bit on conversions on an EJ/EH forum a while back ??

Google EJ/EH forum or similar keywords and it might come up??
I can't think what to write here so this will do.
Top
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

Maybe something in here for you?? :arrow: http://forum.ejehclubqld.com/ehclub/forum/
I can't think what to write here so this will do.
Top
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

Or here ?? :arrow: http://www.64eh.com/Forums/tabid/59/Default.aspx
I can't think what to write here so this will do.
Top
FantaC
Posts: 58
Joined: Wed Jun 17, 2009 11:26 pm
State: NOT ENTERED

Post by FantaC »

thanks guy`s
8)
Top
mrs ratbox

Post by mrs ratbox »

like blacky said all you need is the actual parts associated with the auto ie box, converter, flexplate, bolts, shift. crossmember, tailshaft identical
Top
FantaC
Posts: 58
Joined: Wed Jun 17, 2009 11:26 pm
State: NOT ENTERED

Post by FantaC »

Thanks RatBox
have everything but a shifter even have an auto radiator but might get a seperate oil cooler
Spewing cos i replaced the steering colum with an auto colum but i cut the gear lever of and gutted it , so will just settle for a T bar type
or could i fit a manual gear selecter with the auto colum setup ?
Top
User avatar
Devilrod
Posts: 7394
Joined: Fri Apr 30, 2004 12:55 pm
State: VIC
Location: Beaconsfield, Vic

Post by Devilrod »

Don't forget to remove the spigot bearing either...
Speed and Style........... One day I'll get the speed bit.
Top
FantaC
Posts: 58
Joined: Wed Jun 17, 2009 11:26 pm
State: NOT ENTERED

Post by FantaC »

thanks DevilRod
Top
User avatar
Sammy
Posts: 664
Joined: Mon Jun 26, 2006 3:06 pm
State: NOT ENTERED
Location: Tenambit, NSW.
Contact:
Contact Sammy

Post by Sammy »

Devilrod wrote:Don't forget to remove the spigot bearing either...
and put the auto spigot in there!
Regards,

Sammy.

http://www.oldholdens.com
Top
FantaC
Posts: 58
Joined: Wed Jun 17, 2009 11:26 pm
State: NOT ENTERED

Post by FantaC »

Thanks Sammy
Top
Post Reply

Return to “Driveline”