Includes seating, upholstery, door trims, dashboard and heater.
Moderators: reidy , Blacky
DA FLETCH
Posts: 28 Joined: Thu Jun 11, 2009 6:08 pm
State: NOT ENTERED
Location: VARSITY LAKES GOLD COAST
Post
by DA FLETCH » Sun Jul 05, 2009 11:30 am
OOOOOO NO i snaped mine ..i did it very slow ...and even use the same tools ...anyone got a spear...thanks
I LOVE THE WAY SHE MAKE'S ME FEEEEEEL....
Craig
Posts: 1296 Joined: Thu Jun 14, 2007 5:16 pm
State: NOT ENTERED
Location: Fear and Loathing in Brisvegas
Post
by Craig » Mon Jul 06, 2009 6:51 pm
DA FLETCH wrote: anyone got a spear...thanks
Come on its not that bad its only a EK
Better dead than red
EK, the VN of the 60s
bumper
Posts: 717 Joined: Mon Dec 31, 2007 10:07 am
State: TAS
Location: Devonport tasmania
Contact:
Post
by bumper » Sun Apr 04, 2010 11:36 am
was it just the ek's that had this special badge?
wanker????
I'd rather consider myself as an "owner operator"!!
FBEKHOLDENFANS page
https://www.facebook.com/groups/253705454864/
Trev
Posts: 7819 Joined: Thu Apr 15, 2004 6:43 pm
State: NOT ENTERED
Location: Wonthaggi
Post
by Trev » Sun Apr 04, 2010 7:06 pm
Yes
[img]http://i47.photobucket.com/albums/f177/trevwood/WOOFTOsmall.jpg[/img]
Woofto Car Club Member No3
bumper
Posts: 717 Joined: Mon Dec 31, 2007 10:07 am
State: TAS
Location: Devonport tasmania
Contact:
Post
by bumper » Sun Apr 04, 2010 7:32 pm
wanker????
I'd rather consider myself as an "owner operator"!!
FBEKHOLDENFANS page
https://www.facebook.com/groups/253705454864/
Trev
Posts: 7819 Joined: Thu Apr 15, 2004 6:43 pm
State: NOT ENTERED
Location: Wonthaggi
Post
by Trev » Sun Apr 04, 2010 7:53 pm
Brett, I know someone that wants one! Trev
.
[img]http://i47.photobucket.com/albums/f177/trevwood/WOOFTOsmall.jpg[/img]
Woofto Car Club Member No3
Viper
Posts: 108 Joined: Fri Feb 22, 2008 8:57 am
State: NOT ENTERED
Location: Melbourne
Post
by Viper » Fri May 30, 2014 7:46 pm
I managed to get mine off today using some good old WD40 and Luke's method, so cheers. The only question I have is can anyone tell me how to get those retaining clips out that hold the badge on?????
parisian62
Posts: 3996 Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Post
by parisian62 » Sun Jun 01, 2014 8:08 pm
Hi Viper
If you are putting the badge back on just leave the clips there. If you are wanting to smooth over then punch the clips in.
Stewart
Viper
Posts: 108 Joined: Fri Feb 22, 2008 8:57 am
State: NOT ENTERED
Location: Melbourne
Post
by Viper » Sun Jun 01, 2014 8:33 pm
parisian62 wrote: Hi Viper
If you are putting the badge back on just leave the clips there. If you are wanting to smooth over then punch the clips in.
Stewart
Thanks Stewart,
I going to have to punch them in then. Do you know where I can get some replacement ones from then? Or can anyone else tell me? I'm own in Melbourne, so do Rarespares stock them?