Rebuilding of Old Timer (EK wagon)

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

Post Reply
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Contact parisian62

Post by parisian62 »

thanks for the comments. With another 3 pans to go and a lot of other rust spots things have fallen into a routine...cut, weld, grind...cut, weld, grind...

John - :lol: it's really handy having the screwdriver welded there...I've never lost it...it's just a bit difficult to use though.. :lol:

RB - :D with the rate of knots you work at you'll be finished before we get to the 4th pan. No chassis kit...the sqaure tube you can see under the floor is a part of the trolley that ties the front and back wheels together.
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Top
mrs ratbox

Post by mrs ratbox »

no speed no money :( BUT cause i'm leaving in ruff (rat) there's only really the floors to do :) have a motor gearbox need a free or cheap HR front :lol:
Top
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Contact parisian62

Post by parisian62 »

another floor pan goes in...this time the rear pasenger side...with a nice added bonus of the underfloor bracing also requiring attention...this was done March/April this year...cut, weld, grind...

Image

Image

Image

Image

Image

Image

Image
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Top
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Contact parisian62

Post by parisian62 »

OK well we're still cutting, welding and grinding away...this happened from May to September 08...(yeah i know it's slow going)....drivers side bottom of A pillar, inner sill and floor plan...

What we were faced with...
Image

Image

Image

cutting out...
Image

blasting doesn't get all the nasties...
Image

this is roughly about where I started to freak...and said to Loui..."You sure you can put this thing back together again...?" :shock:
Image

Image

I unpicked all the spot welds from a donor section...
Image

Image

Am proud to say I even fired up the mig :oops: and made this adjustable trolley for the front subframe so it could be wheeled into place...
Image

the subframe was bolted back on so we could line up the Y frames to the inner sill...
Image

welding inner sill back into place...
Image

lookin good... 8)
Image

Image

Image

Image

Another top job by Loui with the pan ready for welding in... :D :D :D
Image
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Top
Dave
Posts: 107
Joined: Mon Nov 14, 2005 4:53 pm
State: NOT ENTERED
Location: Perth W.A.

Post by Dave »

Impressive amount of work youre doing.
Looks like youve got patience & a lot of skill.
Keep it up. :D
My Band.....
www.myspace.com/thesuperdextas
Top
mrs ratbox

Post by mrs ratbox »

i was sooking about the rust i had to get done :shock:
makes me feel bad/lazy/guilty i've cut much better cars than this up :oops:

but this one to you has history so there is a point to it :)
Top
Blacky
Posts: 13344
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Post by Blacky »

10 out of 10 for dedication Stewart - your grandfather would be proud.
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
User avatar
Devilrod
Posts: 7394
Joined: Fri Apr 30, 2004 12:55 pm
State: VIC
Location: Beaconsfield, Vic

Post by Devilrod »

Awesome. Well worth the effort, in the long run at least you know its right.
Speed and Style........... One day I'll get the speed bit.
Top
Brown Bear
Posts: 412
Joined: Tue May 24, 2005 3:00 pm
State: NOT ENTERED
Location: Clarence Town, NSW

Post by Brown Bear »

Awesome work there Stewart - this is an awesome business card for Loui...

Are you planning to leave a few holes in the back floor pan for sentimentality?
On safari

Member of FB EK Holden Car Club of NSW Inc.
Top
oldnek
Posts: 1518
Joined: Sun Nov 19, 2006 9:15 pm
State: NOT ENTERED
Location: Ulladulla NSW

Post by oldnek »

Loui's doing a great job there Stewart. bet your glad to have him on board.
"Hey"! how good is it to have a clean slate to work off. Makes for a easier job to work with, when everything is so clean.
There's nothing as Sweet as a EK V8
Top
parisian62
Posts: 3997
Joined: Wed May 11, 2005 2:19 pm
State: NSW
Location: Sydney
Contact:
Contact parisian62

Post by parisian62 »

thanks for the comments and feedback guys. I am stoked by Loui's workmanship - the skill and patience is all his. A couple of times I've said to him "that'll do" and his reply has been "no its being done properly..."

If others need rust repairs...I can ask him...that's after the EK is finished of course... :wink:

BB - no holes but I'm keeping some rust sections hanging up on the garage wall as reminders...
Feelin free in a '61 FB.
Member of FB-EK Holden Car Club Of NSW Inc.
Check out the Rebuild of Old Timer
Top
minifb
Posts: 2416
Joined: Thu May 26, 2005 10:05 pm
State: NOT ENTERED
Location: FBville formally known as JUNEE
Contact:
Contact minifb

Post by minifb »

GREAT JOB MATE.... CHEERS MARK
FB/EKForum member 123
ImageWoofto Car Club Member No4

IF ITS NOT CHOPPED IT MAY ASWELL BE RESTORED

Member FB-EK Holden Car Club of NSW Inc.
Top
Dee
Posts: 143
Joined: Sun Aug 10, 2008 8:53 am
State: NOT ENTERED

Post by Dee »

great work, Stewart.

and another great resto which didn't go belly up and off to the crusher.

I'm thinkin loui must be blewin with his missus..?
Putting a lot of effort into this it makes me think he's gettin more out of this than you - and we know that won't happen..

keep him fokused and don't let him drift from the quality - might have to grease his palm a bit more if he starts to lose the purpose..

cruisin soon..

Dee
Top
EKSPCL
Posts: 794
Joined: Sat Mar 15, 2008 11:36 pm
State: NOT ENTERED
Location: Langwarrin, Victoria

Post by EKSPCL »

Great stuff Parisian62 :wink:
I think I would have just sobbed and walked out after seeing that rust.
My 6yr old daughter said
"Dad your car's looking great! Which end is the front?"
Top
FB MAD
Posts: 2725
Joined: Thu Jun 30, 2005 7:59 pm
State: NOT ENTERED
Location: Upper Hunter N.S.W

Post by FB MAD »

I'd say the fact that it was Stewart's Grandads car ,actually finding it again after being long lost and the memorys it has was all the inspiration that he needed to see this one through.

I guess that part of Louies reward is seeing the big smile on Stewart's face :D .
I can't think what to write here so this will do.
Top
Post Reply

Return to “My FB EK”