Steel timing gear for a EK grey motor
Steel timing gear for a EK grey motor
Where is the best place to buy the timing gears in steel or maybe alloy? Which is the best set to buy?
Re: Steel timing gear for a EK grey motor
I wrote this some time ago, and the info is a little dated:
http://www.fbekholden.com/forum/viewtop ... de#p205186
The table weighing up the pros and cons is still correct.
Most of the steel gears being flogged by resellers appear to be the Speco MFXCAM units. I've used them before (and am about to put one into Grace's ute), though others have found significant backlash issues with them (can't remember if it was Craig or Greg?).
JP still do the alloy gears (JP5986 alloy).
To the best of my knowledge, Master don't do the gear sets anymore. I have not touched base with Diecrest.
Cheers,
Harv
http://www.fbekholden.com/forum/viewtop ... de#p205186
The table weighing up the pros and cons is still correct.
Most of the steel gears being flogged by resellers appear to be the Speco MFXCAM units. I've used them before (and am about to put one into Grace's ute), though others have found significant backlash issues with them (can't remember if it was Craig or Greg?).
JP still do the alloy gears (JP5986 alloy).
To the best of my knowledge, Master don't do the gear sets anymore. I have not touched base with Diecrest.
Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
- Craig Allardyce
- Posts: 1464
- Joined: Sun Aug 07, 2011 7:26 pm
- State: VIC
- Location: Stratford
Re: Steel timing gear for a EK grey motor
My backlash problem was due to the gear being flogged out from crank vibrations after running one of those crap Durabond balancers on the grey.Harv wrote: ↑Tue Apr 27, 2021 8:42 am I wrote this some time ago, and the info is a little dated:
http://www.fbekholden.com/forum/viewtop ... de#p205186
Most of the steel gears being flogged by resellers appear to be the Speco MFXCAM units. I've used them before (and am about to put one into Grace's ute), though others have found significant backlash issues with them (can't remember if it was Craig or Greg?).
Re: Steel timing gear for a EK grey motor
While we're on the subject, I have a new alloy gear to go on the rebuilt motor in the Ute, but no crank gear with it. I have two crank gears which have done many miles in stock engines with fibre gears, one of which fibre gears did fail. They look fine to my somewhat myopic eyes. Should I replace or should the used ones be ok? This is a red motor by the way.
FB ute driver, EK van project
FB ute driver, EK van project
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie
Re: Steel timing gear for a EK grey motor
I would have said reuse the crank gear.
Some people like a "matched set", but for most uses the old gear will be fine.
Cheers,
Harv
Some people like a "matched set", but for most uses the old gear will be fine.
Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
Re: Steel timing gear for a EK grey motor
If it's for a red motor, definitely replace the crank gear as well. Not because of any wear-related problems, but because red motor timing gear sets are as cheap as chips compared with grey.
Rob
Rob
Re: Steel timing gear for a EK grey motor
Thanks fellas. I picked up the cam gear and seal for $10 on Gumtree. I'll price a crank gear.
FB ute driver, EK van project
FB ute driver, EK van project
getting my FB ute on the road
EK van on rotisserie
EK van on rotisserie
Re: Steel timing gear for a EK grey motor
Thanks Harv the best workshop instruction manual ever seen Hopefully we wont need it going to Toowoomba!
-
- Posts: 790
- Joined: Thu Jul 02, 2020 3:04 am
- State: SA
Re: Steel timing gear for a EK grey motor
Good info in this thread -thanks very much!
I just rang die crest and their gear sets are $440 + postage... also they only do straight cut gears.
So yes it seems pricey and I'm unsure about what straight cut will be like.
Found this option on ebay with Resto Country for $199 + postage... helical cut timing gear only, no matching crank gear.
I rang Resto Country and they said it is a Speco VHT brand timing gear...
How does that sound to you guys, would you buy it?
https://www.ebay.com.au/itm/40200193154 ... 0903.m5276
I just rang die crest and their gear sets are $440 + postage... also they only do straight cut gears.
So yes it seems pricey and I'm unsure about what straight cut will be like.
Found this option on ebay with Resto Country for $199 + postage... helical cut timing gear only, no matching crank gear.
I rang Resto Country and they said it is a Speco VHT brand timing gear...
How does that sound to you guys, would you buy it?
https://www.ebay.com.au/itm/40200193154 ... 0903.m5276
Drew
Re: Steel timing gear for a EK grey motor
I'd buy the helical cut timing gear on its own. You don't need to replace the crank gear, and only need straight-cuts if you are chasing every poofteenth of power out of the thing (or love driveline chatter).
Hunt round for the best price on the steel gear.
Cheers,
Harv
Hunt round for the best price on the steel gear.
Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.