blueys ute rip'n'strip

stillute-ed · Post by **stillute-ed** » Sat Jul 11, 2009 7:03 pm

BLUEYS got a new engine crane and motor stand

time to start the rip'n'strip

ok so first up wonder whats under this lot and

BUGGER I CAN SEE WHATS GOING ON HERE

(BUGGER) (ME)

gunna clean this up a bit

parisian62 · Post by **parisian62** » Sat Jul 11, 2009 7:12 pm

Bluey looks like she's got everything under control.

Stewart

J · Post by J » Sat Jul 11, 2009 7:50 pm

looking good (well apart from the rust!)
keep posting pics mate!

if you get stuck for grey motor bits I may have a few

blue ute · Post by **blue ute** » Sat Jul 11, 2009 10:56 pm

J wrote:if you get stuck for grey motor bits I may have a few

Hmmmm like what J ??

EK283 · Post by **EK283** » Sun Jul 12, 2009 7:49 am

Yep,

Thats a genuine FB

It has rust in all the correct places

Looks like lots of fun in front of you.

Regards Greg

oldnek · Post by **oldnek** » Sun Jul 12, 2009 9:14 am

Bluey's well trained he's got those boxes of snap lock bags for and all.

stillute-ed · Post by **stillute-ed** » Thu Jul 16, 2009 8:38 pm

ok so got the rip'n'strip a bit further. been a busy week i'll start on the front sub frame tomorrow

stillute-ed · Post by **stillute-ed** » Fri Jul 17, 2009 11:35 pm

bl@#$y rusted bolts got them in the end at least there's no more rust under the sub frame at the fire wall . the sill sections wern't a surprise

oldnek · Post by **oldnek** » Sat Jul 18, 2009 12:14 am

I know this sounds silly, But thats a clean rusty car, if you know what I mean.

Good to see your getting into her.

Regards John

arty64 · Post by **arty64** » Sat Jul 18, 2009 6:21 pm

Take your time ,do it right the first time,then u got no problems later,looking forward to seeing progress.

stillute-ed · Post by **stillute-ed** » Sun Jul 19, 2009 5:49 pm

got her mobile on the floor today

stillute-ed · Post by **stillute-ed** » Wed Aug 12, 2009 9:44 pm

started on the rotissery hope to have it finished in the next couple of weeks so i can turn the ute into a big roast chook.
covered in metal shavings and wd40 some jobs just suck.

Thommo · Post by **Thommo** » Thu Aug 13, 2009 6:19 pm

stillute-ed wrote: covered in metal shavings and wd40 some jobs just suck.

Just give yourself a good shake outside and get your
master to give you a good warm wash before you jump on the lounge bluey

stillute-ed · Post by **stillute-ed** » Thu Aug 13, 2009 9:18 pm

thanks for the tip thommo might get a scratch under the chin as well depending what mood she's in (master that is)

stillute-ed · Post by **stillute-ed** » Tue Sep 08, 2009 9:14 pm

YE.HA PIG ON A SPIT . finally got the ute up on the rotisery still getting used to it being up on its side now i can see how bad the rust is and have now found some repairs done in the past so there's more than we knew about .(thought that would be the case )so were not at the bottom of the hole yet .the real fun starts soon .the screw drivers will be replaced with bolts in the next couple of days for those with a keen eye .thanks garry for the rotisery photos on his post i'm going to paint them later on.