Page 1 of 1
Wagon number plate light lense
Posted: Thu Apr 10, 2008 10:58 pm
by Malcolm
Ok all you wagon owners, can anyone show me how a lense fits to a wagon rear bumber number plate light (the ones in the overiders)
Pickies would be good
Thanks
Posted: Fri Apr 11, 2008 6:04 am
by mattymartin
hey malcolm
sorry mate, havent got that far yet... my old one didnt have any...
i look forward to this response though as it'll be useful to me later...
matty martin
Posted: Fri Apr 11, 2008 7:39 am
by thropzed
Hey I'll be watching for this as well. I just picked up a mint set at gold coast super swap with no lenses and want to fit them asap.
Come on you wagon owners!!!
Cheers Theo Z.............
Posted: Fri Apr 11, 2008 9:09 am
by mrs ratbox
can you buy new wagon lenses
Posted: Fri Apr 11, 2008 9:22 am
by Thommo
ratbox wrote:can you buy new wagon lenses
Yes, through the Victorian club.
Ph Sam, (03)5822 1379
Posted: Fri Apr 11, 2008 1:24 pm
by Sammy
my old ek wagon had like perspex or something on them
Posted: Fri Apr 11, 2008 4:48 pm
by yeprat1
im up for a set didnt realize u could buy them new
Posted: Fri Apr 11, 2008 7:55 pm
by MINT62
gday malcolm
...what thommo said, still havnt aquired a set myself yet
let us know how you get on
regards ray
wagon number plate light lense
Posted: Fri Apr 11, 2008 8:22 pm
by Malcolm
I gave Sam a call and he doesn't have any left and he's not making more any time soon. So I went and got a piece of lexon (like perspex only tougher) and am going to make a set.
Posted: Fri Apr 11, 2008 8:57 pm
by ben
Not speaking for all wagon owners, but some of us don't even have any overiders
.......must be all you wan-t-be sedan drivers snaping them up
Re: wagon number plate light lense
Posted: Fri Apr 11, 2008 9:28 pm
by Craig
Malcolm wrote:I gave Sam a call and he doesn't have any left and he's not making more any time soon. So I went and got a piece of lexon (like perspex only tougher) and am going to make a set.
Named after Ben Lexen who developed it also the desiner of the twin keel on Australia 2 developed at Bulimba in Brisbane Sorry Im full of usless shite
Re: wagon number plate light lense
Posted: Mon Apr 14, 2008 8:21 am
by Dr Terry
Craig wrote:Malcolm wrote:I gave Sam a call and he doesn't have any left and he's not making more any time soon. So I went and got a piece of lexon (like perspex only tougher) and am going to make a set.
Named after Ben Lexen who developed it also the desiner of the twin keel on Australia 2 developed at Bulimba in Brisbane Sorry Im full of usless shite
Sorry, that's not quite correct. Ben 'Lexcen' did develop the twin keel for the Australia II. However 'Lexan' clear synthetic sheet (which is tougher than Perspex) has been around for decades.
Dr Terry.
Posted: Mon Apr 14, 2008 8:36 pm
by Craig
Bugger Thought I Knew something
Posted: Mon Apr 14, 2008 8:43 pm
by Trev
Craig wrote:Bugger Thought I Knew something
Your not Robinson Caruso Craig, infact I'm wrong daily, the other day I thought I was rite but it worked out I was wrong again
, Trev
Posted: Mon Apr 14, 2008 10:20 pm
by hammondo
I think Ben Lexcen did design the original tarago for toyota though, then they named the toyota lexcen (commodore) after him in honour when he died. Thats going off old memory though!