Page 47 of 83
Re: Chev EK
Posted: Fri Mar 13, 2020 6:37 am
by EK283
Thanks Clay,
I've had the dreaded door fall off and bend the bottom corner scenario !!! Only once and never again.
Greg
Re: Chev EK
Posted: Sun Mar 15, 2020 9:07 am
by rosco
Looks a great result, Greg...
Clay, this is why we use guide coat - there is not one ripple in that panel that I can see..
On the matter of dropping doors - yep, done that..... rear left. Color coats on, was blocking the final coat down with the door sitting on a large square panel of wood.. it was on top of a bench stool...... bumped it and the lot fell to the concrete floor.
Upper right corner of the window frame bent over at 90 deg, huge dent in the door main body........ back to the panel shop... took another two weeks to recover to where that panel was........ no more panels of wood or bench stools.... I do panels on the floor now, on soft blankets... or - fitted to the vehicle...
As for reducer... with the little bit of experience I now have with spraying 2K (boat)... I altered the ratio of reducer (which is similar to thinners in an arylic system) according to temperature and humidity.... lower temperature - less reducer... that worked for me with both the 2K primer and also 2K top coats.... I used exactly the recommended mix of hardener.
frats,
Rosco
Re: Chev EK
Posted: Sun Mar 15, 2020 7:58 pm
by FCEKHKZD
not FB EK, but another project working on about 300 hrs in filler primer and paint etc,all the blocking pays off, sorry to hilack thread
Sent from my iPhone using Tapatalk
Re: Chev EK
Posted: Mon Mar 16, 2020 5:57 am
by Harv
Verodo Green?
Cheers,
Harv
Re: Chev EK
Posted: Mon Mar 16, 2020 9:12 am
by EK283
Green !
Green is nice !!!!
Greg
Re: Chev EK
Posted: Mon Mar 16, 2020 9:25 am
by FCEKHKZD
Harv wrote:Verodo Green?
Cheers,
Harv
verdoro green yes harv
Sent from my iPhone using Tapatalk
Re: Chev EK
Posted: Mon Mar 16, 2020 12:06 pm
by Errol62
Girl up the roads dad had one new that colour was a HT. Also Mr Tregenza one of my teachers but that was later 1975. Both had the gold stripes.
Sent from my SM-G973F using Tapatalk
Re: Chev EK
Posted: Tue Mar 17, 2020 4:15 pm
by EK283
5th favourite car the Munro !!!!!
Sandblasted and painted all the bits and pieces I have left apart from the panels, getting there finally.
- IMG_0899.JPG (145.87 KiB) Viewed 770 times
- IMG_0900.JPG (253.04 KiB) Viewed 770 times
- IMG_0902.JPG (143.64 KiB) Viewed 770 times
- IMG_0903.JPG (118.13 KiB) Viewed 770 times
I've had 3 EK's and none of them had the front guard bracing as in the last two pictures, has anyone got a photo of where they go please.
Regards Greg
Re: Chev EK
Posted: Tue Mar 17, 2020 4:22 pm
by Errol62
They go from the top bonnet catch cross bar outer end bolt through inner guard, angling down at about 60 degrees and out to the bumper outer rear nut bolt through bottom front of guard. You must have had the lightened racing body cars. 8)8)8)
Sent from my SM-G973F using Tapatalk
Re: Chev EK
Posted: Tue Mar 17, 2020 5:56 pm
by Brett027
Forgot posted these a while back
Sent from my SM-T865 using Tapatalk
Re: Chev EK
Posted: Tue Mar 17, 2020 5:57 pm
by Brett027
Not forgot! Rosco.
Sent from my SM-T865 using Tapatalk
Re: Chev EK
Posted: Tue Mar 17, 2020 6:00 pm
by EK283
Thanks,
That's great probably would have been head scratching.
Greg
Re: Chev EK
Posted: Wed Mar 18, 2020 1:55 pm
by rosco
Brett027 wrote: Tue Mar 17, 2020 5:57 pm
Not forgot! Rosco.
Sent from my SM-T865 using Tapatalk
Did I forget something, Brett?...
frats,
Rosco
Re: Chev EK
Posted: Wed Mar 18, 2020 2:09 pm
by Brett027
Not likely!
It was auto correct. I typed Rosco, it changed it to forget. Auto Correct is the worst and best of things...
Sent from my Pixel using Tapatalk
Re: Chev EK
Posted: Thu Mar 19, 2020 8:53 am
by rosco
Thanks Brett,
had me scratching what is left of my fading grey matter.... pun intended.
frats,
Rosco
