Re: Wayne with a Sydney 1961 FB
Posted: Sun Mar 17, 2013 8:44 pm
WHY do you want a black ek toCal wrote:Looking awesome, Wayne.
Wish I had your garage
fbekholden.com
FB-EK Holden Car Clubs of Australia
https://www.fbekholden.com/forum/
Wayne with a Sydney 1961 FB
Page 16 of 23
Re: Wayne with a Sydney 1961 FB
Posted: Sun Mar 17, 2013 8:47 pm
No Rusty, the actual garage 
Re: Wayne with a Sydney 1961 FB
Posted: Mon Mar 18, 2013 7:10 am
You must be stoked with that Wayne.
Re: Wayne with a Sydney 1961 FB
Posted: Mon Mar 18, 2013 4:35 pm
Milkshakes's doors open and close with no problems at all.
And we used a Rarespares rubber kit....
http://youtu.be/mEZvkZlr84c
And we used a Rarespares rubber kit....
http://youtu.be/mEZvkZlr84c
Re: Wayne with a Sydney 1961 FB
Posted: Mon Mar 18, 2013 5:14 pm
The rubber at the bottom is hanging out, Wayne 
Re: Wayne with a Sydney 1961 FB
Posted: Mon Mar 18, 2013 5:18 pm
My rubber has been hanging out since I was old enough to know why.....Cal wrote:The rubber at the bottom is hanging out, Wayne
Really the sill plates arn't in yet ya dick!.....
Re: Wayne with a Sydney 1961 FB
Posted: Tue Mar 19, 2013 7:23 am
You showoff!Milkshakes's doors open and close with no problems at all.
I'm jealous... 
Re: Wayne with a Sydney 1961 FB
Posted: Tue Mar 19, 2013 7:31 am
Sounds just like a Golf.parisian62 wrote:You showoff!Milkshakes's doors open and close with no problems at all.
Re: Wayne with a Sydney 1961 FB
Posted: Tue Mar 19, 2013 1:12 pm
Milkshake ... 
........Looking good mate .......damn nice colour ........Fingers
........Looking good mate .......damn nice colour ........Fingers Re: Wayne with a Sydney 1961 FB
Posted: Tue Mar 19, 2013 5:58 pm
A bit more from today
Almost finished the sound deadner on the roof
Going to fill up the missing bits after I do the floor.
I'm over painting floors I tell ya.
Must be 3 coats of POR15 and the last today was black enamel. This FB will never rust in my lifetime.
Cheers
Almost finished the sound deadner on the roof
Going to fill up the missing bits after I do the floor.
I'm over painting floors I tell ya.
Must be 3 coats of POR15 and the last today was black enamel. This FB will never rust in my lifetime.
Cheers
Re: Wayne with a Sydney 1961 FB
Posted: Wed Mar 20, 2013 9:52 pm
Have you tried sticking the sound mat to the POR15 how did it go?
I am doing the same to mine after I finally paint it would like to know if I need to scuff it up or not let us know how you go
I got some matting off ebay resomat got sh@tloads will be doing the roof and the floors interior side of firewall boot lid etc.
I am doing the same to mine after I finally paint it would like to know if I need to scuff it up or not let us know how you go
I got some matting off ebay resomat got sh@tloads will be doing the roof and the floors interior side of firewall boot lid etc.
Re: Wayne with a Sydney 1961 FB
Posted: Wed Mar 20, 2013 10:30 pm
I painted over the por15 with enamel.
Sticks like glue.
Ring me any time and have a yarn mate.
Sticks like glue.
Ring me any time and have a yarn mate.
Re: Wayne with a Sydney 1961 FB
Posted: Fri Mar 22, 2013 10:30 pm
Thanks I will
Re: Wayne with a Sydney 1961 FB
Posted: Fri Mar 22, 2013 11:35 pm
My firewall sound deadener arrive today, can't wait to install it.
Cost $170 from John Warren Victoria we found it in the FE FC Forum
His mobile is 0411 316 137 email john@classicgloveboxes.com
Thought I'd put the floor mats in to settle them
so out in the sun to warm them up, they need a trim but I'm not complaining.
Boot came up a treat.
Installed the rubber flappy things under the bonnet to keep the dust out
And yes I know there EK but didn't have an option, I may change them later.
Made them myself from a template I brought off ebay and the rubber from good old Clark Rubber.
You might find this interesting, I spent a good part of a week cleaning and polishing the decoration that goes
on the sill covers, that was a shit of a job put as there's no repo avaiable it had to be done (Les at Rarespares note!)
I used a hobby knife to scrape out 50 years of dirt and grine and polished with Purple Stuff.
They look great.
Before
After
Thats all Kiddies
Cheers.
Cost $170 from John Warren Victoria we found it in the FE FC Forum
His mobile is 0411 316 137 email john@classicgloveboxes.com
Thought I'd put the floor mats in to settle them
so out in the sun to warm them up, they need a trim but I'm not complaining.
Boot came up a treat.
Installed the rubber flappy things under the bonnet to keep the dust out
And yes I know there EK but didn't have an option, I may change them later.
Made them myself from a template I brought off ebay and the rubber from good old Clark Rubber.
You might find this interesting, I spent a good part of a week cleaning and polishing the decoration that goes
on the sill covers, that was a shit of a job put as there's no repo avaiable it had to be done (Les at Rarespares note!)
I used a hobby knife to scrape out 50 years of dirt and grine and polished with Purple Stuff.
They look great.
Before
After
Thats all Kiddies
Cheers.
Re: Wayne with a Sydney 1961 FB
Posted: Sun Mar 24, 2013 4:52 pm
Rustydungers (Russell) Came around Saturday afternoon and put the taillights and bumpers on.....
While I watched and took piccies...
Don't you say a word Stewart....
Altho I put the new rubber dust protectors on the taillights...
Used these bolts and washers to do that..got em at bunnings!...
So I got the front one together.....
And it looks like this now.....
How good does the back look, the chrome just adds to the car...
I also put the dust protector on the rear beaver panel but didn't take pics ...sorry.
While I watched and took piccies...
Don't you say a word Stewart....
Altho I put the new rubber dust protectors on the taillights...
Used these bolts and washers to do that..got em at bunnings!...
So I got the front one together.....
And it looks like this now.....
How good does the back look, the chrome just adds to the car...
I also put the dust protector on the rear beaver panel but didn't take pics ...sorry.