Need ID of some parts

If it doesn't fit below then post here and see if another FB EK fanatic can help you out.

Moderators: reidy, Blacky

Mick
Posts: 4272
Joined: Sun Sep 26, 2010 8:47 am
State: NSW
Location: Coffs Harbour NSW

Re: Need ID of some parts

Post by Mick »

1. correct 4 hubcaps :thumbsup: other 3 EK worth nothing up to what the idiots pay $50each
2.rear sway bar probly any early holden, usually good money on ebay
3. red motor oil pump once again worth nothing, except if there is a large cross on the other side then maybe $50 up
4. no idea
5. sports mufflers look like 2" but hard to tell maybe $50 - $100 i'll give you $20 if they're straight through 2" and yor goin to clarendon
6.top bar here bonnet locks down on FB/EK goes from side to side between guards maybe 0- $20
7.gearbox cross members to suit hadfield chassis kit
8. push in oil cap for aftermarket chrome rocker cover, water neck from holden V8 other bits no idea worth a couple of bucks
9.fabricated gearbox crossmember at a guess out of EJ/EH possably could be used in auto body EK once again a few bucks
10. might be the rare EK mnaual heavy duty radiator as it looks like an auto one but seems to have dfferent part No and only 1 outlet
11. i think is EK auto
12. EH auto
all radiators 0 - maybe $50
13. part of a hadfield chassis kit goes on subframe where front end bolts up, worth probly nothing
sometimes yor just better off shitting in yor hands and clapping

W.S.C.C.A
Woodstock chapter
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Need ID of some parts

Post by WayneXG95 »

Thanks Mick, anyone else?
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
User avatar
MeFB
Posts: 1717
Joined: Wed Oct 26, 2011 2:08 pm
State: NOT ENTERED
Location: WA and Lumut

Re: Need ID of some parts

Post by MeFB »

Those wire/spoke wheel trim thingys would have to be worth a buck or two on ebay? I haven't seen anything like those before.

:arrow: :D
Alan
Member No.1 of the FB EK Holden Car Club of WA (Woo-hoo :D sweet!)
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Need ID of some parts

Post by WayneXG95 »

WayneXG95 wrote:4th up 4 wire type hubcaps, no id name or numbers?

Image
Been advised these have been seen on EK's years ago..Need dress rims to attach to wheel...and a moon style insert...might be why I have one.. :)
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
ek61
Posts: 1419
Joined: Sun May 29, 2005 10:09 pm
State: NOT ENTERED
Location: FB-EK HOLDEN CAR CLUB OF SA INC

Re: Need ID of some parts

Post by ek61 »

NO 4
they are fruit bowls you just have them upside down :)

look like wire wheel inserts to me but wouldnt have a clue what the would be off 8) 8)
"THE JOURNEY OF A THOUSAND MILES BEGINS WITH A BROKEN FAN BELT AND A FLAT TYRE"
***just cruise***
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Need ID of some parts

Post by WayneXG95 »

I'D the wire wheel covers. 56 Chevy. Be checking if I can restore them.
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
resto
Posts: 27
Joined: Sat Dec 31, 2011 7:30 pm
State: NOT ENTERED
Location: Melbourne

Re: Need ID of some parts

Post by resto »

Image

Here you go - you need the outer rim to make them worth anything - It is a very thin dish shaped rim

Resto
User avatar
WayneXG95
Posts: 2565
Joined: Wed Sep 07, 2011 9:42 am
State: NSW
Location: Sydney

Re: Need ID of some parts

Post by WayneXG95 »

Guess I better start looking. Anyone got these? :D
Wayne Chambers
President
FB EK Holden Car Club of N.S.W
Post Reply