Speco floorshift for crashbox

ekv8ute · Post by **ekv8ute** » Thu Jul 10, 2008 6:28 pm

Has anybody got a photo of a speco floorshift set up on a grey motor crash box? I have a complete shifter and linkages but I think it's from a later gearbox.

The shift mechanism doesn't have a model number on it so I guess only the linkages were different?

Thommo · Post by **Thommo** » Thu Jul 10, 2008 8:35 pm

Gday ekv8ute
Check this thread out.....

Click Here
It should have the info you need

Cheers
Jeff

ekv8ute · Post by **ekv8ute** » Sat Jul 12, 2008 9:05 am

Thanks Jeff,
Good info there but I have a different shifter!

Mark

Craig · Post by **Craig** » Sat Jul 12, 2008 11:49 am

ekv8ute wrote:Has anybody got a photo of a speco floorshift set up on a grey motor crash box? I have a complete shifter and linkages but I think it's from a later gearbox.

The shift mechanism doesn't have a model number on it so I guess only the linkages were different?

Nope Holden made 3 different 3 speeds all floor shifts are different

Thommo · Post by **Thommo** » Sat Jul 12, 2008 1:40 pm

ekv8ute wrote:Has anybody got a photo of a speco floorshift set up on a grey motor crash box?

Gday Mark
I linked you to that thread because it had a pic of a speco floorshift set up on a grey motor crash box
to make it easy to compare what you have to a early set-up

Cheers
Jeff

ekv8ute · Post by **ekv8ute** » Sat Jul 12, 2008 4:40 pm

Here is my shifter-i think it might be for a later gearbox.

I can fit the linkages to the original selector and shift levers on the gearbox- i am more interested in how the shifter mounts to the gearbox.The mount I have (not shown) looks like it should bolt to where a bellhousing bolts up.

Thommo · Post by **Thommo** » Sat Jul 12, 2008 5:44 pm

Hi Mark
Do you want that shifter to operate a non synchro crashbox?

ekv8ute · Post by **ekv8ute** » Sun Jul 13, 2008 5:38 pm

Yeah Thommo.Played with it today and mocked it into place-can't figure out how the selector linkage ties in with the other linkage.Do you have any words of wisdom?

Mark

Thommo · Post by **Thommo** » Sun Jul 13, 2008 6:38 pm

Hi Mark

It would be easier to make the crashbox shifter.

Your shifter has two linkages to shift two selectors on a synchro gearbox.
The stick operates either linkage by moving across from one to the other.

The non-synchro crashbox has one selector that selects all gears.
That one selector moves back & forth for 1st/reverse,
then slides out on a shaft to select 2nd & 3rd.
The stick pivots from the very bottom, which slides the selector in & out.

They are two differant actions altogether
requiring two differant shifters.

Have a look at the earlier link to the other thread,
they are easy to make.

Cheers
Jeff

ekv8ute · Post by **ekv8ute** » Sun Jul 13, 2008 6:54 pm

Thanks Jeff,

Looks to be a pretty easy project!Thanks for your help.

Mark

ps any ideas what box my shifter is for?

Thommo · Post by **Thommo** » Sun Jul 13, 2008 7:07 pm

ekv8ute wrote:ps any ideas what box my shifter is for?

Nope

Craig · Post by **Craig** » Sun Jul 13, 2008 8:33 pm

Syncro box I would say not sure but seen similar in HQdont know if the syncro box changed from HKTG to HQ

fbekholden.com

Speco floorshift for crashbox

Speco floorshift for crashbox

Re: Speco floorshift for crashbox

Re: Speco floorshift for crashbox