Chev EK

[TAZ]

cheers Greg, I will check mine to see if one will fit

Bugger i only have 840mm between the rails thanks again for measuring.

[Mick]

Hi Mick,

I started to cut it for the brackets but then decided to make new ones.

I will take a pic and post it this arvo.

It really should be cut and redone its just I had found another one quick so went down that path.

Regards Greg

thanks

[EK283]

Mick,

shots of the front end

The attachment WP_20180925_16_16_59_Pro.jpg is no longer available

WP_20180925_16_17_05_Pro.jpg (892.86 KiB) Viewed 617 times

[EK283]

Bloody hell to many good looking originals I better save the day for us hot rodders

Finished the front end completely today, thank god for that !!!!

So its UC Torana with offset upper arms, extended Camaro top ball joints, HZ stubs with Harrop steering arms and Leyland discs. HQ steel PBR callipers, Pedders standard height V8 springs and shitty Monroe shocks ( they just don't feel right when I bled them to soft I reckon.)

WP_20180928_16_50_09_Pro.jpg (1.59 MiB) Viewed 600 times

WP_20180928_16_50_53_Pro.jpg (1.84 MiB) Viewed 600 times

Also GQ patrol sway bar links and a HR heavy sway bar from Whiteline

More tomorrow

Regards Grg

[Blacky]

Greg, what is your front track width wheel face to wheel face with that setup mate ?

[EK283]

Hi Blacky,

Funny you should ask that cause I measured it today for the first time, it was pretty rough no wheel alignment yet but around 1400mm.( wheel mounting face to face )

Regards Greg

[Mick]

Mick,

shots of the front end
WP_20180925_16_16_59_Pro.jpg
WP_20180925_16_17_05_Pro.jpg

you've sold it ?

[Blacky]

Hi Blacky,

Funny you should ask that cause I measured it today for the first time, it was pretty rough no wheel alignment yet but around 1400mm.( wheel mounting face to face )

Regards Greg

Thanks mate, will check it against a modded HR front - I am in 2 minds which way to go for the 2 door EK

[gpi]

are you getting custom brake hoses made up?

[EK283]

Mick,

shots of the front end
WP_20180925_16_16_59_Pro.jpg
WP_20180925_16_17_05_Pro.jpg

you've sold it ?

No Mick,

You must have sped read, the photo attachment is no longer available !
If your interested let me know.

Regards Greg

[EK283]

Hi Blacky,

Funny you should ask that cause I measured it today for the first time, it was pretty rough no wheel alignment yet but around 1400mm.( wheel mounting face to face )

Regards Greg

Thanks mate, will check it against a modded HR front - I am in 2 minds which way to go for the 2 door EK

Shit loads of work goes into the modification but then again what doesn't take work, no pain no gain !!!!!

Regards Greg

[EK283]

are you getting custom brake hoses made up?

Yes mate had them made up, I just need a couple of copper washers then they are in !!

Regards Greg

[EK283]

Major disaster yesterday my son and I thought yep its time to throw the donk in but unfortunately a major fail.

When I built the exhaust I had the motor in an out several times and I just couldn't work out what the issue was this time around, it just wouldn't fit in.

So after a lot of swearing and cursing (especially because of scratching the new ceramic coated headers) we abandoned play. After looking back at some photos I suddenly realised that the sump that I used to build the pipes with the motor out doesn't fit between the gaps of the pipes ARGGGGGHHHHHH. So I am going back to a standard sump without the wings today and try again.

WP_20180929_15_45_56_Pro.jpg (1.68 MiB) Viewed 513 times

WP_20180929_15_46_05_Pro.jpg (1.77 MiB) Viewed 513 times

WP_20180929_15_48_22_Pro.jpg (1.72 MiB) Viewed 513 times

This fun just wont end, as they say back to the drawing board !!!!!

Regards Greg

[thebrotherj]

dammit, that sucks Greg!

I imagine you've tried everything to make it fit the way it is... is the high volume sump specced for a reason? Are you planning on racing this car like the Stude?

[Mick]

Mick,

shots of the front end
WP_20180925_16_16_59_Pro.jpg
WP_20180925_16_17_05_Pro.jpg

you've sold it ?

No Mick,

You must have sped read, the photo attachment is no longer available !
If your interested let me know.

Regards Greg

yeah it wasn't till after that i realised the pic was no longer available