Neil's FB Station Wagon

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

User avatar
Errol62
Posts: 10302
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neil's FB Station Wagon

Post by Errol62 »

Did you see what I did there?


Sent from my iPhone using Tapatalk
getting my FB ute on the road
EK van on rotisserie
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

Yes mate I get it :eh: :eh: :roll: :roll:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

So I suppose overall progress is that I basically have all of the repairs completed to the floors/lower half of the body, I do have a little bot on the passenger side dog leg to do.
I'm about to put the rear independent end under the wagon with tyres on to make sure that I have enough clearance between the diff cradle and the body before welding in the piece of sheetmetal that replaces the original diff hump, a couple of smaller dents and repairs, sort out a fuel tank, I think it will be a sedan tank sideways in the space once these smaller bits are sorted then The Rev is going to Keith's who is going to help me do the roof change and the firewall that needs replacing hopefully this will be early in the new year all going to plan :esurprised: :crazy: :crazy:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

So a little time in the shed yesterday after assembling a small shed for the mother in law on Saturday :ebiggrin:
Driver dog leg finally finished, had to do another small repair inside the wheel well in behind the dog leg, tidied it up some and then moved over to the other horror show, melted the lead out of it and will attack it next. :roll: :roll:
IMG_2387.JPG
IMG_2387.JPG (4.03 MiB) Viewed 397 times
IMG_2388.JPG
IMG_2388.JPG (4.3 MiB) Viewed 397 times
IMG_2389.JPG
IMG_2389.JPG (5.77 MiB) Viewed 397 times
IMG_2390.JPG
IMG_2390.JPG (4.18 MiB) Viewed 397 times
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

Still have to have a grinding party and clean up the welds in the back seat area, anyone wish to join :crazy: :crazy:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Errol62
Posts: 10302
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neil's FB Station Wagon

Post by Errol62 »

Haven’t forgot that FB indicator housing mate.


Sent from my iPhone using Tapatalk
getting my FB ute on the road
EK van on rotisserie
Blacky
Posts: 12816
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Neil's FB Station Wagon

Post by Blacky »

FireKraka wrote: Mon Oct 21, 2024 2:04 pm Still have to have a grinding party and clean up the welds in the back seat area, anyone wish to join :crazy: :crazy:
Carpet will hide them :thumbsup:
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

That's what I was thinking Blacky dyno-mat covers everything :lol: :lol: :lol: but the last time Keith came down for a beer and to see how I was going he looked at it and said "hope your going to clean that up" :lol: :lol: so I had better make an attempt at some stage :wtf:

Thanks Clay I do think I have a couple but not sure how good they are, they are in the stash somewhere :roll:

I now seem to have a full set of FB Wagon trim now thanks to what Blacky has dragged home recently and to Laurie Armato in Bendigo

Ok so onwards and upwards :ebiggrin: :ebiggrin:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

Got a bit of time yesterday on the passenger side dog leg, think I have all the big patches in, bit more of a clean up inside the wheel arch and have to chase some pin holes.
IMG_2417.jpeg
IMG_2417.jpeg (3.09 MiB) Viewed 300 times
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Errol62
Posts: 10302
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neil's FB Station Wagon

Post by Errol62 »




FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

Finished the passenger side bottom of the dog leg on Sunday
IMG_2423.JPG
IMG_2423.JPG (4.26 MiB) Viewed 197 times
Now I need to weld in the clearance plate for the independent rear suspension so I have moved the suspension under the back end, get it into the hangers then I can make sure I have enough clearance and also check tyre clearance.
It isn't in the hangers yet that's why it doesn't look centered under the diff hump :roll:
IMG_2424.JPG
IMG_2424.JPG (3.82 MiB) Viewed 197 times
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

After struggling with a couple of jacks and some strong words I was able to get the rear end into the wagon, I have room around the suspension so will be able to weld the plate in.
IMG_2429.jpeg
IMG_2429.jpeg (2.77 MiB) Viewed 120 times
IMG_2430.jpeg
IMG_2430.jpeg (2.55 MiB) Viewed 120 times
Wheels are in the centre of the wheel arch
IMG_2431.jpeg
IMG_2431.jpeg (2.64 MiB) Viewed 120 times
Once I get some tyres on it I can lower it onto the ground and set the shock height.
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Errol62
Posts: 10302
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neil's FB Station Wagon

Post by Errol62 »

Looks awesome Neil!


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
User avatar
FireKraka
Posts: 2434
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neil's FB Station Wagon

Post by FireKraka »

Looking at tyre spacing had a couple of 225/50/16’s fitted to rims and put them on this afternoon when I got home, have room but may need to roll the wheel arch a little.
IMG_2434.jpeg
IMG_2434.jpeg (3.16 MiB) Viewed 57 times
IMG_2435.jpeg
IMG_2435.jpeg (3.43 MiB) Viewed 57 times
Obviously it is not on the ground yet, have set the coil over shock height once I have weight on it but pretty happy with it at the moment. :esmile:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Blacky
Posts: 12816
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Neil's FB Station Wagon

Post by Blacky »

can ya pull the coilovers out and put a jack under the tyre to get it up into the wheel tub ?
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Post Reply