LS1EK

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

Blacky
Posts: 12703
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: LS1EK

Post by Blacky »

It’s sorting out fiddly things like that that gobble up so much time …..
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
EK283
Posts: 2394
Joined: Thu Mar 16, 2006 9:51 pm
State: NSW
Location: SYDNEY NSW

Re: LS1EK

Post by EK283 »

Good work Taz,

My engineer wanted a heat shield around the Borgeson steering joint, initially I wrapped the header pipe with fibreglass but that caused it to rust.

It did pass however and at the moment i'm looking at making a more permamnent solution.

Greg
So many cars so little time!
User avatar
FireKraka
Posts: 2368
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: LS1EK

Post by FireKraka »

A win is a win Taz tick it off the list and move on to the next one, hopefully the list is getting smaller :crazy:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
The Reverend FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Ummm I think I have achieved something this afternoon. Another 3 hours tidying up the wiring and trial fitting things. At least when it goes together there will be no drilling or welding .

Thinking of going for the patina look on the body. I have the door a quick scuff and found the original paint under what the previous owner had applied 😊
Attachments
32A6C183-3574-49A3-8409-D14D6A0012B7.jpeg
32A6C183-3574-49A3-8409-D14D6A0012B7.jpeg (2.13 MiB) Viewed 1119 times
7E8F5582-E824-4879-9C03-B9F1D300A49D.jpeg
7E8F5582-E824-4879-9C03-B9F1D300A49D.jpeg (3.44 MiB) Viewed 1119 times
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Layed out the engine harness tonight and positioned more wiring inside the car. Will need adapters for the injector connections to the loom as the truck manifolds run a different injector to the standards LS1.
Attachments
7889582B-6B5C-4E28-B5FC-4463360FF1C6.jpeg
7889582B-6B5C-4E28-B5FC-4463360FF1C6.jpeg (3.44 MiB) Viewed 1090 times
AA2C8072-2A84-46E7-8B4A-1A78D789CD4A.jpeg
AA2C8072-2A84-46E7-8B4A-1A78D789CD4A.jpeg (3.66 MiB) Viewed 1090 times
B080845F-3C0D-4800-916A-A638DE2CAC7D.jpeg
B080845F-3C0D-4800-916A-A638DE2CAC7D.jpeg (3.52 MiB) Viewed 1090 times
Blacky
Posts: 12703
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: LS1EK

Post by Blacky »

Man those truck manifolds are big , guessing you will fab up a cover for it mate ???
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Yeah Blacky, starting on a cover for the engine soon that will incorporate the throttle body air intake into it as well. Maybe something similar to what is in the photo.
Attachments
35B2B378-385E-4B9C-A927-74F95C0CFC09.jpeg
35B2B378-385E-4B9C-A927-74F95C0CFC09.jpeg (312.5 KiB) Viewed 1019 times
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Fabbed up a battery box for the boot, not sure I will use the lid.

Also playing with the patina a paint look for the exterior. Paint will all need to come off as I do not know what it is like under it. Thoughts on the best way to get back to the original colour, tried acetone and thinners and the grey will not budge.

Also can get a cheap set of 17” cragars but front are 8” anyone know if they can fit with a custom back spacing?
Attachments
IMG_0669.png
IMG_0669.png (2.13 MiB) Viewed 948 times
IMG_0660.jpeg
IMG_0660.jpeg (2.06 MiB) Viewed 948 times
IMG_0665.jpeg
IMG_0665.jpeg (2.13 MiB) Viewed 948 times
IMG_0662.jpeg
IMG_0662.jpeg (2.22 MiB) Viewed 948 times
Blacky
Posts: 12703
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: LS1EK

Post by Blacky »

I think 8” would be a battle , can you cut and reweld them ???
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
User avatar
Errol62
Posts: 10163
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: LS1EK

Post by Errol62 »

Rub away with 400 is my only suggestion.

Maybe if you can get them to clear the tie rod end with say zero offset. Even then they will rub if the car is low. I'm running 195 on two different 14" rims. Sampson's rub, custom steelies don't. They have about 5mm more offset positive.

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Blacky wrote: Sun Jul 16, 2023 9:52 pm I think 8” would be a battle , can you cut and reweld them ???
Yeah thought if that but the barrels are a one piece I think but then again I could get a 17” barrel and use the centre in that.

17” steelies are going to cost me $900 and then I have to get them modified for the wheel track so I thought these could be an alternative. Still might work if I can get a 17”” barrel.
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Okay, have bitten the bullet and started to remove the wiring so I can get it all set out out nicely. Mate was back briefly who is doing the wiring and discussed a way forward. I will cut what has to be cut for removal and he will add in plugs later as required.

This will hopefully mean I can finally get the car back on the rotisserie so I can run all the brake and fuel lines before painting underneath and inside the car.
Attachments
IMG_0841.jpeg
IMG_0841.jpeg (3.2 MiB) Viewed 864 times
Blacky
Posts: 12703
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: LS1EK

Post by Blacky »

That wiring looks scary 😳😳
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
TAZ
Posts: 340
Joined: Wed Sep 23, 2015 9:32 pm
State: TAS
Location: hobart

Re: LS1EK

Post by TAZ »

Blacky wrote: Mon Jul 31, 2023 9:54 am That wiring looks scary 😳😳
I think once I lay it out flat I will get it heading in the right direction….. well I think so 🤣
In the Shed
Posts: 1983
Joined: Wed May 16, 2012 10:18 pm
State: SA
Location: South Australia

Re: LS1EK

Post by In the Shed »

Blacky wrote: Mon Jul 31, 2023 9:54 am That wiring looks scary 😳😳
Looks like a Mumbai telephone exchange 🤔
A day in the shed beats a day at work!
Post Reply