Ute tail gate.

Looking for a new daily driver, the next project, or maybe a parts car? try here first...

Moderators: reidy, Blacky

Post Reply
User avatar
oz_ek
Posts: 429
Joined: Sat Oct 31, 2015 8:22 pm
State: VIC
Location: Victoria

Ute tail gate.

Post by oz_ek »

Looking for an inner ute tail gate, previous owner customized this one!
P1070788.JPG
P1070788.JPG (184.19 KiB) Viewed 500 times
P1070789.JPG
P1070789.JPG (365.58 KiB) Viewed 500 times
gpi
Posts: 1131
Joined: Mon Apr 26, 2010 2:08 pm
State: VIC

Re: Ute tail gate.

Post by gpi »

baby jesus wept
User avatar
oz_ek
Posts: 429
Joined: Sat Oct 31, 2015 8:22 pm
State: VIC
Location: Victoria

Re: Ute tail gate.

Post by oz_ek »

gpi wrote: Fri Jul 15, 2022 8:35 pmbaby jesus wept
Nice work hey!
This one is actually off an FE/FC, I've had it for years and often look at it and wonder if the inner skin was removed just to slap that bog in the badge mounting holes?
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Ute tail gate.

Post by Errol62 »

Maybe lightened for speed Phil?

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
User avatar
oz_ek
Posts: 429
Joined: Sat Oct 31, 2015 8:22 pm
State: VIC
Location: Victoria

Re: Ute tail gate.

Post by oz_ek »

Errol62 wrote: Fri Jul 15, 2022 9:45 pm Maybe lightened for speed Phil?

Sent from my SM-G781B using Tapatalk
I had started looking into having some Pullmax tooling made to reproduce the swage lines of the inner skin, that was before most machine shops closed their doors due to Covid.
Blacky
Posts: 12171
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Ute tail gate.

Post by Blacky »

oz_ek wrote: Fri Jul 15, 2022 10:07 pm
Errol62 wrote: Fri Jul 15, 2022 9:45 pm Maybe lightened for speed Phil?

Sent from my SM-G781B using Tapatalk
having some Pullmax tooling made to reproduce the swage lines of the inner skin
That right there is your answer , is there a decent metal fab place nearby that could make up a patch piece ????
When you're faced with an unpleasant task that you really don't want to do, sometimes you just have to dig deep down inside and somehow find the patience to wait for someone else to do it for you.


Foundation member #61 of FB/EK Holden club of W.A.
User avatar
oz_ek
Posts: 429
Joined: Sat Oct 31, 2015 8:22 pm
State: VIC
Location: Victoria

Re: Ute tail gate.

Post by oz_ek »

Blacky wrote: Sat Jul 16, 2022 10:11 am
oz_ek wrote: Fri Jul 15, 2022 10:07 pm
Errol62 wrote: Fri Jul 15, 2022 9:45 pm Maybe lightened for speed Phil?

Sent from my SM-G781B using Tapatalk
having some Pullmax tooling made to reproduce the swage lines of the inner skin
That right there is your answer , is there a decent metal fab place nearby that could make up a patch piece ????
Had one bloke have a crack at it, but the panel warped too much.....Similar to what can be seen at the 1:35 mark in this clip..... https://www.youtube.com/watch?v=EBdwCQ5l0eE
gpi
Posts: 1131
Joined: Mon Apr 26, 2010 2:08 pm
State: VIC

Re: Ute tail gate.

Post by gpi »

try planishing the area first before swaging
Post Reply