Page 1 of 2
Anyone know this chop?
Posted: Tue Aug 18, 2020 7:37 pm
by FBeing
As the title says does anyone know anything about this chopped van?
I haven’t been through the forum to check (yes. I’m lazy) and a mate just sent it to me, he saw it on a US FaceAche page. I’m not on FaceAche.
Looks to be NSW. And I’m sure I’ve seen it before but it was black? Maybe even matte black? A ratbox job??
Sent from my iPhone using Tapatalk
Re: Anyone know this chop?
Posted: Tue Aug 18, 2020 7:56 pm
by Devilrod
Nup, no idea....
Was this an old build on here? I did a half arse look and didn’t find anything.
Re: Anyone know this chop?
Posted: Tue Aug 18, 2020 8:25 pm
by FJWALLY
Surely that would never pass engineering ?
Sent from my iPhone using Tapatalk Pro
Re: Anyone know this chop?
Posted: Tue Aug 18, 2020 8:42 pm
by Errol62
I don't know. Could you fit a carton through the window?
Sent from my SM-G973F using Tapatalk
Re: Anyone know this chop?
Posted: Tue Aug 18, 2020 8:44 pm
by FJWALLY
Errol62 wrote:I don't know. Could you fit a carton through the window?
Sent from my SM-G973F using Tapatalk
Cans maybe - lol but you couldn’t see past the bonnet
Sent from my iPhone using Tapatalk Pro
Re: Anyone know this chop?
Posted: Tue Aug 18, 2020 11:21 pm
by CHOPPED
i have been keeping an eye on this one
don't think its been on the forum but have been following it on Facebook
he was asking about a windscreen for it
i read the half arsed reply's from people that obviously had no idea and decided to not comment and keep my mouth shut
very cool looking
my ute has a 4 inch chop so this i would think has 6 inches
i guess he will find me if he needs advice
paul
Re: Anyone know this chop?
Posted: Wed Aug 19, 2020 1:14 am
by 60Special
I’m pretty sure that this is Ned Kelly’s van.
Re: Anyone know this chop?
Posted: Wed Aug 19, 2020 5:00 am
by gpi
Re: Anyone know this chop?
Posted: Wed Aug 19, 2020 8:05 am
by Devilrod
That was the one I was thinking of!
Re: Anyone know this chop?
Posted: Wed Aug 19, 2020 5:00 pm
by FBeing
Yes! I thought I had seen it, and yes it was Ratbox!
Thanks.
Still no idea how it will get past rego...
Re: Anyone know this chop?
Posted: Fri Aug 21, 2020 6:39 pm
by axeman
I beleive this belongs to stanley on here ,who bought it off me ,it had a 71/2 inch chop done on it ,my blown and injected ute has 8 inch roof chop done on it ,good see the van again ,hope its on the road in NSW
Re: Anyone know this chop?
Posted: Fri Aug 21, 2020 6:45 pm
by gpi
where do you get your inspiration from?
Re: Anyone know this chop?
Posted: Fri Aug 21, 2020 8:19 pm
by Errol62
Stanley got blocked
Sent from my SM-G973F using Tapatalk
Re: Anyone know this chop?
Posted: Fri Aug 21, 2020 8:37 pm
by Mick
i commented on the original post
Re: Anyone know this chop?
Posted: Fri Aug 21, 2020 10:58 pm
by Blacky
Errol62 wrote: ↑Fri Aug 21, 2020 8:19 pm
Stanley got blocked
not by me - just checked and his account is still active ???