Project 2.

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

Similar but bespoke to our dash shape.
Sucker for a rusty bomb
Blacky
Posts: 12171
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Project 2.

Post by Blacky »

Lookig good mate, how much drama was it setting the air conditioning up ???
When you're faced with an unpleasant task that you really don't want to do, sometimes you just have to dig deep down inside and somehow find the patience to wait for someone else to do it for you.


Foundation member #61 of FB/EK Holden club of W.A.
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

None Blacky. The Retro Air unit does demisters, heater and cool and because of that there is a lot of large diam ducting to get in the dash space. I had planned to run a vent on drivers side but could not route the duct to it in the available space. The Mini Gen 2 unit has two central vents so one of those will do drivers side. It has the same type of options as modern car units so I can get cooling and heating to come to floor and vents simultaneously on one setting so should be fine without a far right hand vent.
As for ease of install, no dramas. The evaporator fits snuggly behind glove box ( one mount is a longer bonnet hinge bolt through firewall and other two on dash panel support. To fit the wiring kit and ducting in the space, the glovebox has to go. With the addition of my centre console there is zero net loss of space, but that part is the only compromise.
If your engine can run the compressor then the rest is easy. Because I couldn't, one hose from the evaporator runs under carpet on the floor along the drive shaft hump, through cab wall and to the electric compressor. The long hose from the condensor runs accross through LHS inner guard and then follows inside front guard along inner guard panel, down K Frame leg and along under floor coming through floor up next to compressor in rear.
The kit comes with home use fittings but I got my hoses made up using hydraulic crimps. The hose fittings are all O ring type and are straight forward to fit and in my case nothing leaked straight up. Bought a condensor unit to fit radiator dimensions and that was easy to install onto radiator support panels using rubber mounts. Beware that the bonet locking plate needed to move out a few mm's to clear condensor, and the horn will no longer fit in the original position as it hits the condensor - mine now sits on drivers side inner opposite fuel pump. Other than that it is a very straightforward job.
No dramas installing it all. I may have to fit an electric fan if engine cooling becomes problematic but haven't done the drive tests as yet. Check it out at Echuca.
Sucker for a rusty bomb
User avatar
funkyscooter
Posts: 543
Joined: Wed Aug 16, 2017 8:12 am
State: NSW
Location: Sydney

Re: Project 2.

Post by funkyscooter »

Nice one Brett - love the subtle inserts in the door cards matching the seat trim. Are the seats Subaru still? They look in good condition.
Scott
(Not so rusty) Ol' Rusty - FB/EK Sedan
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

Yep, Forester. Best $100 bucks spent.
Sucker for a rusty bomb
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Project 2.

Post by FireKraka »

Interior looks great Brett, seats look really comfy, and appreciate the air con install blurb I'm planning to aircon Frank I think.
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

[/image]Here is the other side.
Attachments
20230127_190706.jpg
20230127_190706.jpg (1.69 MiB) Viewed 409 times
Sucker for a rusty bomb
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

Project 2 is ready for engineering check next week. Lots of rough panel work to finish off in the coming years and also a bit of buffing to do before Echuca. Should be a reliable and playful ride.
Attachments
20230215_191522.jpg
20230215_191522.jpg (3.5 MiB) Viewed 308 times
20230215_191303.jpg
20230215_191303.jpg (3.12 MiB) Viewed 308 times
20230215_191317.jpg
20230215_191317.jpg (2.72 MiB) Viewed 308 times
20230215_191358.jpg
20230215_191358.jpg (3.2 MiB) Viewed 308 times
20230215_191538.jpg
20230215_191538.jpg (2.54 MiB) Viewed 308 times
Sucker for a rusty bomb
User avatar
Harv
Posts: 5020
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Project 2.

Post by Harv »

Beautifully done.

That colour really suits it - modern enough to be noticeable, but subtle enough to be similar to an original colour.

Good luck with the engineer.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Project 2.

Post by Errol62 »

Looks great Brett. Flash us yer jugs??? 8)

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
In the Shed
Posts: 1872
Joined: Wed May 16, 2012 10:18 pm
State: SA
Location: South Australia

Re: Project 2.

Post by In the Shed »

Looks very sharp Brett 👍 Like the jelly beans, what size tyres are on them?

Regards
Stephen
A day in the shed beats a day at work!
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

Thanks Harv, yes the colour works well. Plenty of body work still to do to finish it properly: but not for a while.
Clay I have no idea what you want to see and am afraid to ask.
Stephen tyres are 185 R80 13s. Spare is 155 R80 13 and fits neatly in the hole.
Sucker for a rusty bomb
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: Project 2.

Post by Brett027 »

Some more pics
Attachments
20230216_115041.jpg
20230216_115041.jpg (3.04 MiB) Viewed 256 times
20230216_115142.jpg
20230216_115142.jpg (3 MiB) Viewed 256 times
Sucker for a rusty bomb
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Project 2.

Post by Errol62 »

I mean carbys Brett. Used to call them jugs...

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
In the Shed
Posts: 1872
Joined: Wed May 16, 2012 10:18 pm
State: SA
Location: South Australia

Re: Project 2.

Post by In the Shed »

Brett027 wrote: Thu Feb 16, 2023 11:45 am
Stephen tyres are 185 R80 13s. Spare is 155 R80 13 and fits neatly in the hole.
👍 thanks
A day in the shed beats a day at work!
Post Reply