Neils Frankenstein Ute

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

EK283
Posts: 2328
Joined: Thu Mar 16, 2006 9:51 pm
State: NSW
Location: SYDNEY NSW

Re: Neils Frankenstein Ute

Post by EK283 »

Halfa pad = hot mate !!

Greg
So many cars so little time!
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

So I tackled the brake upgrade on the weekend.
This is what the old rotors looked like coming off you can see some blue spots around the rotors and what felt like some minor cracks around the slots.
IMG_1141.jpg
IMG_1141.jpg (2.49 MiB) Viewed 874 times
IMG_1149.jpg
IMG_1149.jpg (3.52 MiB) Viewed 874 times
IMG_1150.jpg
IMG_1150.jpg (3.43 MiB) Viewed 874 times
So pulled all that off :roll: the hub/adapters came with new bearings and dust seals so hubs on.
IMG_1142.jpg
IMG_1142.jpg (2.51 MiB) Viewed 874 times
IMG_1143.jpg
IMG_1143.jpg (2.55 MiB) Viewed 874 times
Then rotors.
IMG_1144.jpg
IMG_1144.jpg (3.28 MiB) Viewed 874 times
And of course not all goes a smoothly as they tell you in the fairy tales :lol: went to put the caliper on and couldn't get it to line up with the holes in the stub axle/drop spindle :roll: when I looked at the spindle and then at the caliper realized I had to do a little adjustment :crazy:
Spindle
IMG_1146.jpg
IMG_1146.jpg (2.78 MiB) Viewed 874 times
Adjustment of the caliper, I could have taken some off of the spindle I suppose but the caliper was easier in my mind.
Caliper adjustment, I haven't cut into the caliper as such just sliced some off flat with the bolt hole face to give the clearance it needed to go back just that little bit more so the bolts lined up.
IMG_1145.jpg
IMG_1145.jpg (3.45 MiB) Viewed 874 times
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

So to finish up.
The caliper was now able to bolt up
IMG_1147.jpg
IMG_1147.jpg (3.07 MiB) Viewed 872 times
Took me quite a long time to get them to bleed up, doesn't really help when you are by yourself :roll: ended up getting my vacuum bleeder and sucking a fair bit of fluid through then finished off by pump and release and they came up pretty good.
Haven't had it on the road yet just in and out of the shed and they seem a whole lot better, I disconnected the line to my booster from the vacuum pump and it seemed pretty good from the vacuum pump but I am also still not convinced that the booster is working 100% either so probably something else to look at.
When I was reading up about doing the brake upgrade they all said you need at least 15" I'm running 16" rims and from the look of the the photo I think 15's might even be a push, I suppose it would depend on which front end setup you are running.
IMG_1152.jpg
IMG_1152.jpg (3.74 MiB) Viewed 872 times
I hope this helps anybody else wanting to do the upgrade. :thumbsup:
Neil
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Harv
Posts: 5020
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Neils Frankenstein Ute

Post by Harv »

G'day Neil,

I'd be interested to see how you routed the brake hoses please. I'm not overly happy with how I've done the ones on the meth monster project.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neils Frankenstein Ute

Post by Errol62 »

That look much more betterer neil

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
User avatar
oz_ek
Posts: 429
Joined: Sat Oct 31, 2015 8:22 pm
State: VIC
Location: Victoria

Re: Neils Frankenstein Ute

Post by oz_ek »

Caliper doesn't contact the upper control arm on full lock?
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

Harv I ran the hoses back between the spindle and the shock tower cause the hose was too short to go on the outside of the spindle but the hose is ok on full lock both ways.

Oz I notched the upper control arm when I fitted the VP Calipers and as I said I haven't given it a test drive yet to see how it goes, might have nto make some adjustments :roll:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Harv
Posts: 5020
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Neils Frankenstein Ute

Post by Harv »

FireKraka wrote: Tue Feb 22, 2022 12:34 pm Harv I ran the hoses back between the spindle and the shock tower cause the hose was too short to go on the outside of the spindle but the hose is ok on full lock both ways.
Cool - if it is OK, I'd love some photos please. I ran the hoses from the caliper inboard, then between the subframe and swaybar end. Hose-to-hardline bracket on the subframe, but much further forward than the old drum hoess. It works, but even with HR brake hose spring-thingies the routing is not very elegant.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

So I did some test runs last weekend and the upgrade has vastly improved my brake situation, re adjusted my wheel bearings yesterday as I had them a little tight I think and all looking good also have full turning lock to lock without any drama.
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neils Frankenstein Ute

Post by Errol62 »

That’s good news Neil. You’re going to need those brakes in about 2700km, and you will need a good turning circle to chuck a right at Bord Agudda.


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

So a bit of an update on the VT brake upgrade I have found that when I'm on full lock that the brakes fade really bad, having a look at it it looks like one of the brake lines pulls tight and restricts fluid so I'm going to have new hoses made and add about 6" so the hoses can't kink when on lock :crazy:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
EK283
Posts: 2328
Joined: Thu Mar 16, 2006 9:51 pm
State: NSW
Location: SYDNEY NSW

Re: Neils Frankenstein Ute

Post by EK283 »

FireKraka wrote: Tue Mar 22, 2022 10:55 am So a bit of an update on the VT brake upgrade I have found that when I'm on full lock that the brakes fade really bad, having a look at it it looks like one of the brake lines pulls tight and restricts fluid so I'm going to have new hoses made and add about 6" so the hoses can't kink when on lock :crazy:
I would to !!! You seriously don't want to tear a hose off and then need to stop in a hurry.

Doesn't modifying these old girls create a challenge !!!!

Greg
So many cars so little time!
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

Tell me about it Greg :lol: Fault finding and problem solving are part of what I do so I do like getting my head around some of these issues.

What's the saying "if it was easy everybody would be doing it" :lol:
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Neils Frankenstein Ute

Post by Errol62 »

Caves Beach motor trimmers are using Frankenstein I their eBay ad.TONNEAU COVER (TARP) for FE,FC,FB,EK HOLDEN FLAT TOP + PRESS STUDS (TNSTC014FT) | eBay
https://www.ebay.com.au/itm/15323696949 ... gKSPPD_BwE

Sent from my SM-G781B using Tapatalk

getting my FB ute on the road
EK van on rotisserie
User avatar
FireKraka
Posts: 2162
Joined: Fri Jan 24, 2014 11:12 am
State: WA
Location: Serpentine, WA

Re: Neils Frankenstein Ute

Post by FireKraka »

Yeah mate it’s been up there for a while I did mention it to him but I don’t really mind I suppose 🤔🤔
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Post Reply