FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Includes fuel system, cooling system and exhaust.

Moderators: reidy, Blacky

madv8bike
Posts: 18
Joined: Wed Mar 30, 2022 7:28 pm
State: QLD

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by madv8bike »

Hey
The no s stamped on top
23 3064
37
Cast in on body
1 3/16
2376436
R

There is also a 213 under the model WW
,

I have a lynx adapter plate , so dont know what it was originally from , but my mate said it worked fine on a 202

Does any of that make sense for u
Ron
But most of my problems is the cam and lifters , I think , just set the lash on hydraulic lifters at 10 thou , like solids now it runs and drives but seems lazy
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by Errol62 »

HQ 253 manual Nov ‘72 on


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
madv8bike
Posts: 18
Joined: Wed Mar 30, 2022 7:28 pm
State: QLD

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by madv8bike »

Thanks for that ,
User avatar
Errol62
Posts: 9664
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by Errol62 »

They generally run ok on mild 186. Similar jetting to 186S. I’m not familiar with the 2600S jetting, though I bought a 161 with similar 253 carb but HX from memory, so people do run them on 161. Harv may have the 2600S jet sizes.


FB ute fixer upper, EK van on rotisserie
getting my FB ute on the road
EK van on rotisserie
madv8bike
Posts: 18
Joined: Wed Mar 30, 2022 7:28 pm
State: QLD

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by madv8bike »

They look like a good simple carby ,
User avatar
Harv
Posts: 5020
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by Harv »

Errol62 wrote: Sat Apr 02, 2022 9:51 pm They generally run ok on mild 186. Similar jetting to 186S. I’m not familiar with the 2600S jetting, though I bought a 161 with similar 253 carb but HX from memory, so people do run them on 161. Harv may have the 2600S jet sizes.

Looks like he's solved his problem now (misadjusted lifters), but for the curious:

His WW (23-3064) was from the HQ 253ci engines with manual transmission.
The only 161ci WW (23-3041) was fitted to the LC GTRs.

His carb has smaller idle tubes (#69 drill vs. #66 drill on the LC). The fuel fed to the idle needle valve will be a poofteenth richer than the 161 needs. The idle needle valve will need backing off slightly.

His carb has different power bypass valves (0.032/0.057" vs. 0.020/0.064" on the LC). These are two stage power bypass valves. At approximately 3-7” Hg (1½-3½psi) manifold vacuum the primary is open and his carb will run richer than the 161 needs (0.032" hole versus 0.020" hole). At 10-12”Hg (5-6psi) the secondary is open and his carb will run leaner than the 161 needs (0.057" hole versus 0.064" hole). Whether this will make a difference depends very much on how he drives the car and what cam duration is installed.

His carb has a smaller pump discharge jet (#71 drill versus #68 drill on the LC). The pump duration spring is the same on these carbs, so his carb will have a slower squirt of fuel when he mooshes the throttle compared to what the 161 needs. Will probably be fine unless he gets initial hesitation when on the loud pedal.

Main metering jets are the same (0.050").

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
Brett027
Posts: 2265
Joined: Thu Apr 18, 2019 4:14 am
State: NSW

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by Brett027 »

Wow Harv. You are amazing! I will be pestering you to do the same for Project 2's WW on it's186s set-up soon😁
Sucker for a rusty bomb
madv8bike
Posts: 18
Joined: Wed Mar 30, 2022 7:28 pm
State: QLD

Re: FB/EK Holden Stromberg Carburetion Enthusiasts Guide

Post by madv8bike »

Hey thanks for all that info , ,,,, great info ,
Post Reply