Front end width required

Includes shock absorbers, springs and steering linkages.

Moderators: reidy, Blacky

Post Reply
Blacky
Posts: 12755
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Front end width required

Post by Blacky »

Hey guys , could someone please measure a stock front end for me ? I need to know the wheel face to wheel face width , preferably in inches ........

Thanks in advance !!!
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
User avatar
Craig Allardyce
Posts: 1464
Joined: Sun Aug 07, 2011 7:26 pm
State: VIC
Location: Stratford

Re: Front end width required

Post by Craig Allardyce »

inside or outside face Blacky?
Top
Blacky
Posts: 12755
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Front end width required

Post by Blacky »

Wheel mounting face on the drum please Craig , looking to buy a straight axle setup while I am in the US and need to know what width I need.
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
User avatar
NoMAD
Posts: 1992
Joined: Thu Sep 29, 2005 5:07 pm
State: WA
Location: Perth, WA

Re: Front end width required

Post by NoMAD »

Blacky wrote:Wheel mounting face on the drum please Craig , looking to buy a straight axle setup while I am in the US and need to know what width I need.
YESSS! DO IT!

(bring back extra ones mate)

Cheers
Nathan
FB/EK Holden Car Club of W.A. Inc
Foundation Member
Top
kelleigh54
Posts: 242
Joined: Wed Apr 25, 2007 12:43 am
State: WA
Location: PERTH WESTERN AUSTRALIA
Contact:
Contact kelleigh54

Re: Front end width required

Post by kelleigh54 »

Gooood Mooorning America ! OK Mr Black , have measured up Maggots EJ and I cant imagine anything different to FB / EK . Took measurement on the deck so as it is in a loaded state and measured between outer face of backing plates directly below king pin which is 1262mm and then backing plate to drum face with calipers is 76mm ( 3inch ) x2 =152mm being a total of 1414mm .The outer edge of drum is proud of the mounting face by about 1mm so pulling that away from both sides will be a grand total of 1412mm or 55.59 inches .Give me a shout when your back bloke as I need that workshop manual , have to rebuild the Quadrajet on the Statesman . Hate the bloody things , bits and pieces flying everywhere and then figuring where it all came from .
I would rather work on a Morris 1100 than use a computer !!!!!!
Top
Blacky
Posts: 12755
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Front end width required

Post by Blacky »

Thanks mate :ebiggrin: will drop it off in a couple of weeks when I get back - too busy having fun over here ATM :D :D :D
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
kelleigh54
Posts: 242
Joined: Wed Apr 25, 2007 12:43 am
State: WA
Location: PERTH WESTERN AUSTRALIA
Contact:
Contact kelleigh54

Re: Front end width required

Post by kelleigh54 »

:D :D :D Well that's obvious , you should be in bed at this time of the morning getting some beauty sleep ....... You need it :P
I would rather work on a Morris 1100 than use a computer !!!!!!
Top
Blacky
Posts: 12755
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Front end width required

Post by Blacky »

Harsh :cry: :cry:





















....... But true :lol: :lol:
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
User avatar
Craig Allardyce
Posts: 1464
Joined: Sun Aug 07, 2011 7:26 pm
State: VIC
Location: Stratford

Re: Front end width required

Post by Craig Allardyce »

Blacky wrote:Wheel mounting face on the drum please Craig , looking to buy a straight axle setup while I am in the US and need to know what width I need.
Sorry Blacky, didn't realise its urgent. I wont be home from work till Sunday Arvo but can do it as the car is on the hoist whilst I'm doing the brake work.
Top
User avatar
Errol62
Posts: 10232
Joined: Sat Dec 06, 2014 2:44 pm
State: SA
Location: Adelaide

Re: Front end width required

Post by Errol62 »

Measured HR disc unladen 1405mm or 55 5/16". Measured EK drum unladen 1397mm which is 55" exactly. Measured EK rear 1420mm or 55 29/32".
Most cars of the era have slightly wider front track so looks like 55 1/2 - 56" would be the go.
getting my FB ute on the road
EK van on rotisserie
Top
Blacky
Posts: 12755
Joined: Tue Jul 20, 2004 8:58 am
State: WA
Location: up in the Perth hills

Re: Front end width required

Post by Blacky »

No stress Craig 8)
I started with nothing and still have most of it left.


Foundation member #61 of FB/EK Holden club of W.A.
Top
Post Reply

Return to “Suspension and Steering”