ok fellas I need help I've got an ek ute with a vn series 2 engine and auto box
I put in an ultimate wiring harness and everyone tells me how easy the VN ECU is to wire up
but I am getting nowhere fast
I do have it turning over
any help please
v6 engine wiring
Re: v6 engine wiring
Firstly - welcome to the forum
Second - you are not giving us much to work with here , can you give us some more info ??? Are you using the EK harness with the VN ECU harness or have you started from scratch ??? Got fuel pressure ? Can you read fault codes ? etc ....
Second - you are not giving us much to work with here , can you give us some more info ??? Are you using the EK harness with the VN ECU harness or have you started from scratch ??? Got fuel pressure ? Can you read fault codes ? etc ....
When you're faced with an unpleasant task that you really don't want to do, sometimes you just have to dig deep down inside and somehow find the patience to wait for someone else to do it for you.
Foundation member #61 of FB/EK Holden club of W.A.
Foundation member #61 of FB/EK Holden club of W.A.
Re: v6 engine wiring
Hi Bematote1
I have done this conversion and wired up my car so as Blacky said give us a bit more detail and I should be able to assist.
Regards
Neil H
I have done this conversion and wired up my car so as Blacky said give us a bit more detail and I should be able to assist.
Regards
Neil H
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
- ekdave1962
- Posts: 413
- Joined: Tue Oct 30, 2007 8:06 pm
- State: NOT ENTERED
- Location: Geelong Vic
Re: v6 engine wiring
hi there i found the guys at delco hacking forum a great help when i wired mine .. including a daughter board to allow usb coms to the ecu which from memory was neeeded to change a few parameters
- ekdave1962
- Posts: 413
- Joined: Tue Oct 30, 2007 8:06 pm
- State: NOT ENTERED
- Location: Geelong Vic
Re: v6 engine wiring
hi there i found the guys at delco hacking forum a great help when i wired mine .. including a daughter board to allow usb coms to the ecu which from memory was neeeded to change a few parameters
Re: v6 engine wiring
Hi Bema
I'm wondering how you are getting on with your wiring I have just had a look at the "Ultimate Wiring harness" website and not sure where your issue may be as I would assume that you are using the original engine harness which should plug straight into your ECU if I remember rightly there is another plug that comes off of the engine harness that the rest of the body harness should then plug into.
As we said before a little more info and we may be able to help mate.
Regards
Neil H
I'm wondering how you are getting on with your wiring I have just had a look at the "Ultimate Wiring harness" website and not sure where your issue may be as I would assume that you are using the original engine harness which should plug straight into your ECU if I remember rightly there is another plug that comes off of the engine harness that the rest of the body harness should then plug into.
As we said before a little more info and we may be able to help mate.
Regards
Neil H
Member of WA FB/EK Car Club
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)
Frankenstein EK V6 Ute
FB Station Wagon Project
1950's Commer Light Truck (2.5 Ton)