Hot grey motor build

Post photos of your pride and joy, or updates on your rebuild!

Moderators: reidy, Blacky

Post Reply
User avatar
Fud
Posts: 74
Joined: Sun Jan 23, 2011 8:29 pm
State: NOT ENTERED
Location: Armidale NSW

Hot grey motor build

Post by Fud »

Picked up a 138 grey today, drove 550km each way to pick it up, what do you do straight after getting home from a 1100km trip? Strip the motor down of course, found a few undesired things in the process, it hey, what are projects without challenges, found 1 bent pushrod, and a lot of milky sludge in the sump and one bore, but looks like a strong base for a rebuild none the less.
User avatar
Fud
Posts: 74
Joined: Sun Jan 23, 2011 8:29 pm
State: NOT ENTERED
Location: Armidale NSW

Re: Hot grey motor build

Post by Fud »

Image
User avatar
Fud
Posts: 74
Joined: Sun Jan 23, 2011 8:29 pm
State: NOT ENTERED
Location: Armidale NSW

Re: Hot grey motor build

Post by Fud »

Image

Imagej
In the Shed
Posts: 1872
Joined: Wed May 16, 2012 10:18 pm
State: SA
Location: South Australia

Re: Hot grey motor build

Post by In the Shed »

Hey Fud,
Was there something special about that motor or was there nothing closer?

Regards
Stephen
A day in the shed beats a day at work!
User avatar
Fud
Posts: 74
Joined: Sun Jan 23, 2011 8:29 pm
State: NOT ENTERED
Location: Armidale NSW

Re: Hot grey motor build

Post by Fud »

Hey Stephen, could not find any closer to home, was told this one spun over but it appears not.

Image
User avatar
Fud
Posts: 74
Joined: Sun Jan 23, 2011 8:29 pm
State: NOT ENTERED
Location: Armidale NSW

Re: Hot grey motor build

Post by Fud »

Got 4 pistons out, the motor is still stuck, time for a big steam clean at work tomorrow and try to get number 3&4 pistons out, followed by the harmonic balancer and the crank and cam. Here are a few photos of pull apart. I am chasing a few pushrods, if anyone has any they don't have a use for anymore, been doing a lot of pushrod research and am about to manufacture my own chrome molly rods.

Image

Image

Image
User avatar
Harv
Posts: 5020
Joined: Mon Oct 08, 2007 2:00 pm
State: NSW
Location: Sydney, Australia

Re: Hot grey motor build

Post by Harv »

Fud wrote: Sun Mar 19, 2017 10:32 pmI am chasing a few pushrods, if anyone has any they don't have a use for anymore, been doing a lot of pushrod research and am about to manufacture my own chrome molly rods.
G'day Fud,

Are you using this info for the moly pushrods?
http://www.fbekholden.com/forum/viewtop ... ly#p216160

One thing to think through (before making moly pushrods) is what you want to do with the valve train. If you are going to use the standard rockers, then hollow moly push rods are not a bad idea. If you want to put roller rockers on it, then you have a few more options. Yella Terra make the grey motor rolly rockys to suit two types of pushrod - the standard "bell end" or cupped grey motor ones, and ball-end ones similar to small block Chev. If you choose the ball-end ones, you will need some different custom pushrods made up. The ball-ends are simpler design (and probably stronger), a poofteenth lighter, and easy enough to get custom made.

Cheers,
Harv
327 Chev EK wagon, original EK ute for Number 1 Daughter, an FB sedan meth monster project and a BB/MD grey motored FED.
User avatar
GreyEJ
Posts: 244
Joined: Sat Oct 30, 2010 8:07 pm
State: VIC
Contact:

Re: Hot grey motor build

Post by GreyEJ »

Any progress on the build?
Post Reply