I'm guessing that a towbar for FE-FC will also suit FB-EK. It depends on whether the locations of the rear bumper bracket bolts got revised. Can anyone confirm or deny?
Rob
Search found 1025 matches
- Sat May 11, 2024 11:35 am
- Forum: Parts wanted
- Topic: Tow bar for EK sedan please
- Replies: 9
- Views: 172
- Wed May 08, 2024 4:16 pm
- Forum: My FB EK
- Topic: Clay’s Wedgewood Blue FB Ute
- Replies: 4396
- Views: 199064
Re: Clay’s Wedgewood Blue FB Ute
. . . wouldn't be anything as simple as headlight high and low beam wires swapped over at the screw terminal blocks?
Rob
Rob
- Tue May 07, 2024 6:07 pm
- Forum: My FB EK
- Topic: Neil's FB Station Wagon
- Replies: 296
- Views: 17619
Re: Neil's FB Station Wagon
Well done, Neil. The doglegs and inner rear wheel arches are about my least favourite repair. You might almost be better off raiding a donor shell for the complete outer section from rear door shutline (where there's a factory seam) to the sill. And we all know that straight, rust-free dogleg sectio...
- Mon May 06, 2024 11:15 am
- Forum: Parts for sale
- Topic: Free to good home - MasterParts Catalogue
- Replies: 6
- Views: 145
Re: Free to good home - MasterParts Catalogue
(raises hand)
Rob
Rob
- Sun Mar 10, 2024 9:15 pm
- Forum: Other Events, Shows etc
- Topic: Local cruise night
- Replies: 10
- Views: 262
Re: Local cruise night
" Hey Charger! "
'Easy on the eye, easy on the wallet', as the ads went.
Rob
'Easy on the eye, easy on the wallet', as the ads went.
Rob
- Thu Mar 07, 2024 12:07 pm
- Forum: General sharing advice and experience
- Topic: Chrome plater recommendation
- Replies: 9
- Views: 395
Re: Chrome plater recommendation
Harv,
You could also try Hamilton Chrome (quite close to Newcastle CBD).
Rob
You could also try Hamilton Chrome (quite close to Newcastle CBD).
Rob
- Thu Feb 22, 2024 12:44 pm
- Forum: My FB EK
- Topic: Project 2.
- Replies: 1484
- Views: 58759
Re: Project 2.
During the development of the GTS 327s, rumour has it that driveshaft failures were frequent. I think it was Tony Roberts who was quoted as saying, "Quite exciting. Bits flying everywhere."
Rob
Rob
- Thu Feb 22, 2024 12:01 pm
- Forum: My FB EK
- Topic: FB Standard Wagon
- Replies: 1127
- Views: 41824
Re: FB Standard Wagon
Drew,
I admire your courage in opening up, on a forum no less.
Umm, who did your seats? The colour and texture of the vinyl is an exact match for my FCs' (note plural possessive) interiors.
(I'd buy the wagon tomorrow if it came up for sale. Just f.y.i.)
Rob
I admire your courage in opening up, on a forum no less.
Umm, who did your seats? The colour and texture of the vinyl is an exact match for my FCs' (note plural possessive) interiors.
(I'd buy the wagon tomorrow if it came up for sale. Just f.y.i.)
Rob
- Wed Feb 21, 2024 7:33 pm
- Forum: Engine
- Topic: Dr Blacky attempts to perform an addagruntome
- Replies: 41
- Views: 1653
Re: Dr Blacky attempts to perform an addagruntome
I recently installed a Merc rear seal in a fellow club member's FJ motor. Compared with the "gasket kit" replacement, it was easy-peasy. Much, much easier to cut. But I found I had to use the crankshaft to set the seal. My fault though. I cut the seal off nearly flush when using a seal set...
- Sun Feb 18, 2024 4:45 pm
- Forum: My FB EK
- Topic: Clay’s Wedgewood Blue FB Ute
- Replies: 4396
- Views: 199064
Re: Clay’s Wedgewood Blue FB Ute
. . . I would almost be inclined to check exhaust valves 1,3,5,6 for poor sealing - on the valve seat . . .
Rob
Rob
- Thu Feb 08, 2024 7:46 pm
- Forum: Brakes, Wheels and Tyres
- Topic: New brakes locked on
- Replies: 3
- Views: 219
Re: New brakes locked on
Option 2: Jack up car Place on axle stands Remove rear wheels Heat circumference of drum with MAP gas torch Start engine, engage reverse, let clutch out If no joy, apply more heat until the brakes begin to free up Don leather gloves and remove smoking-hot brake drums Re-adjust brakes (gift for mecha...
- Tue Feb 06, 2024 9:34 am
- Forum: My FB EK
- Topic: Clay’s Wedgewood Blue FB Ute
- Replies: 4396
- Views: 199064
Re: Clay’s Wedgewood Blue FB Ute
On "8" you'll be struggling to reach 4000.
Nope, set the switch to "4" instead.
Rob
Nope, set the switch to "4" instead.
Rob
- Fri Feb 02, 2024 7:50 pm
- Forum: My FB EK
- Topic: Ammo's Ute
- Replies: 535
- Views: 33597
Re: Ammo's Ute
Sell the alternator for a small fortune to the HKTG crowd as a genuine Monaro part . . .
Rob
Rob
- Mon Jan 29, 2024 5:01 pm
- Forum: My FB EK
- Topic: Clay’s Wedgewood Blue FB Ute
- Replies: 4396
- Views: 199064
Re: Clay’s Wedgewood Blue FB Ute
Clay,
I think you'd want the specified 1/8" pedal free travel when adjusting the master cylinder pushrod. Any less, and the compensating port won't be uncovered . . .
Rob
I think you'd want the specified 1/8" pedal free travel when adjusting the master cylinder pushrod. Any less, and the compensating port won't be uncovered . . .
Rob
- Tue Jan 23, 2024 9:53 am
- Forum: All Holden Day
- Topic: SA All Holden Day 2024
- Replies: 16
- Views: 1856
Re: SA All Holden Day 2024
I would love to have driven over and participated, but events conspired against me . . .
Rob
Rob