Search found 135 matches
- Sun Jan 24, 2021 4:49 pm
- Forum: Interior
- Topic: Speedo Font
- Replies: 1
- Views: 431
Speedo Font
Anyone know the name of the font used in the speedo ?
- Thu Jul 30, 2020 6:05 pm
- Forum: Driveline
- Topic: Gearbox rebuild
- Replies: 6
- Views: 820
Re: Gearbox rebuild
I found that the bearings couldn't be pushed in from the side but did slide down from the top But the smaller bearings were so tight that they wouldn't turn, took me ages to get them out again as they were jammed in tight. the larger bearing seemed to turn OK so i left it in Contacted the seller who...
- Mon Jun 22, 2020 8:27 pm
- Forum: Engine
- Topic: Grey motor pushrod investigations
- Replies: 13
- Views: 4119
Re: Grey motor pushrod investigations
Another problem when they sit in water
Sent from my iPhone using Tapatalk
- Sat Jun 20, 2020 8:39 pm
- Forum: Driveline
- Topic: Gearbox rebuild
- Replies: 6
- Views: 820
Re: Gearbox rebuild
Put the old needle rollers in a bag on the bench and its taken me a week to find them exactly where I left them :oops: Anyhow measured the old Vs new Old New Difference Large 4.755 4.765 0.01 MM Small 3.16 3.18 0.02 MM such a small difference shouldn't cause the problem that I'm having, guessing i'l...
- Wed Jun 10, 2020 9:57 pm
- Forum: Driveline
- Topic: Gearbox rebuild
- Replies: 6
- Views: 820
Gearbox rebuild
Just put a rebuild kit in a standard grey gearbox Problem is I can't fit in all the roller bearings that came in the kit, out of the 3 sets of roller bearings in the gearbox i have one roller bearing that wont fit in each so I have 3 left over (2 small & 1 large) with the bearings in place there...
- Tue Feb 11, 2020 5:11 pm
- Forum: Body, Paint and Panel
- Topic: Roof Cut
- Replies: 6
- Views: 302
Roof Cut
Question:
Can a FC ute Roof cut be transplanted straight onto an FB ute?
Can a FC ute Roof cut be transplanted straight onto an FB ute?
- Fri Jun 28, 2019 11:01 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
Good Analogy carrots
Motor still going strong no knocks or engine rattles
got offered $16k for it last weekend and turned it down having too much fun driving it.
Motor still going strong no knocks or engine rattles
got offered $16k for it last weekend and turned it down having too much fun driving it.
- Tue Jan 08, 2019 7:08 pm
- Forum: Engine
- Topic: SU Carb with extractors
- Replies: 13
- Views: 891
Re: SU Carb with extractors
spent some time tweaking the strommy but couldn't get it to run well with power, the Jet that was in it was a 0.037 tried a 0.051 but when I put the foot down it was like turning the ignition off it just dies, tried a few other combos but nothing was all that good Decided to go with the SU's, had a ...
- Fri Dec 21, 2018 7:05 pm
- Forum: Engine
- Topic: SU Carb with extractors
- Replies: 13
- Views: 891
SU Carb with extractors
while changing the head today I thought I would try out my carby collection I had these twin HS6 SU's for a while now and always wanted to fit them but the fuel bowl hits the #6 extractor pipe and lifts the whole setup by about 1/2 inch. visited the Holden wreckers and looked at 10 sets of extractor...
- Fri Dec 21, 2018 6:20 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
to wrap this up
got the head back today had 12tho taken off, bolted it all back up and it sound mighty.
haven't driven yet as I've now twinged my back and want to rest
thanks to all for the help.
got the head back today had 12tho taken off, bolted it all back up and it sound mighty.
haven't driven yet as I've now twinged my back and want to rest
thanks to all for the help.
- Wed Dec 19, 2018 4:19 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
Yeah not the oil filter, its still on at the moment as its proving to be a bit stubborn coming off
Might have to hammer a screwdriver through it to get it to turn.
Might have to hammer a screwdriver through it to get it to turn.
- Tue Dec 18, 2018 8:25 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
I have no history on the modifications to this vehicle so I only know from google image searches and part numbers I can find to what's been done to it.
- Tue Dec 18, 2018 12:23 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
rear mounted and change welded to clamped Pic's are easy to supply End of steering column under dash https://i1380.photobucket.com/albums/ah170/Robingii/FB/IMG_2058_zpszplqz5rm.jpg http://i1380.photobucket.com/albums/ah170/Robingii/FB/IMG_2055_zpsyy4fagwu.jpg http://i1380.photobucket.com/albums/ah17...
- Tue Dec 18, 2018 8:59 am
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
It's got the standard steering column with a universal joint welded to a shaft that goes through the firewall, then another universal joint to the steering on the front end. Driving along as the camber changes on the road I hardly have to make any steering corrections it just steers straight ahead r...
- Sun Dec 16, 2018 9:37 pm
- Forum: General sharing advice and experience
- Topic: Engine Damage
- Replies: 45
- Views: 2465
Re: Engine Damage
Clutch plate can only go on one way, the springs are biased to one side so if its on the wrong way you cant bolt up the pressure plate.