fbekholden.com

gledge wrote: ↑Wed Apr 17, 2024 11:17 pm If all tuned correctly the only difference is the right foot[emoji3097]

Amen.

Cheers,
Harv

You put a water tap/valve in one of the heater hoses feeding the heater core. Water on = hot air. Water off = warm air because the tap leaks 8) The tap is often put under the engine bay, but can also live inside the car. Get fancy with the tap, and you can run it off the dash control slider thing. Y...

Hi Brett, A man of your caliber needs triple webbers, there is no other marriage for an angry six !! Yes all those cars look awesome, always liked FC's as well. Regards Greg A Holley will do the job, but the induction noise out of a gaggle of Italy's finest is incredible. Some info here if you go t...

Don't ask my children. Every time they drive my car, the fuel gauge pegs over to the left :lol: How they manage to get the car home, and into the driveway with not enough left in it to start is beyond me. Ninja fuel management skills. Pegging to the right means the sender is sending LOTS of resistan...

The little bakelite insulating sleeves, bakelite spring doover and horn contact get fussy on how they are installed. Hint: before pulling ANY of the steering wheel apart, disconnect the battery. That sounds like the kind of advice you would get in a generic Gregory's service manual, but it is for a ...

If you get stuck, I have a puller I can loan you. Easier to troubleshoot if we understand what you pulled apart, and what changed. Was the horn working before you started? How much of the horn bar, steering wheel, horn contacts, honeypot, levers did you pull apart to reinstall 3-on-the-tree? Cheers,...

I went to sea when I was 17 and the ship I was on had a 2 cylinder Lister emergency air compressor, if you got the cranking wrong when you dropped the decompression cocks it would throw you into the bulkhead :lol: :lol: :lol: :lol: They only tell young apprentices about decompression levers after w...

Thanks gents. I've got one of those cable-stoppers on order, and will see if I can make it work. You'd think that a cable-to-valve handle fitting would be common, but not so much in practice. The ARP bolts are 44-47 Rockwell C. On Moh's scale of hardness, they appear here: Hardness Material 1 Talc 2...

A trick I learned from Rob (with thanks).

The cast iron wheel cylinders are fine for daily drivers.

Anything that sits for more than a month between drives needs stainless-lined wheel cylinders.

Cheers,
Harv (master of leaky rear wheel cylinder changes).

Yep, had my share of hand cranking. Back when there was Aerostart and ether, but no Start Ya Bastard. Learned that Lister is a four-letter word. Good thing on the FED is that the huffer lets me run low compression, and I can get a bit of a crank up before unearthing the magneto. Even better is I can...

I am seriously contemplating it. If the IHRA rules let me, and if I need the weight loss to get the FED below the 10.99 second elapsed time class limit, then I will delete the starter motor. The crank fitting will be a little different to the factory GMH one, but will serve the same purpose. Cheers,...

I use a similar setup on a smaller scale for choke on SU carbs. The clamped cable and an over sized bolt head effectively sandwiches the lever, preventing the body from escaping. Ahhh... thankyou. Now I can picture it. Something like this: cable stopper.jpg That might work, if the arm is wide enoug...

I can buy those barrel clamps (cable stops) readily, but can't picture in my head what the assembly would look like?

Cheers,
Harv

Something so simple is driving me nuts. The fuel system on the FED needs a fuel shutoff valve. This is a simple ball valve with AN flared fittings, and a 1/4" thick handle that moves through 90º. The valve is operated via a bowden cable from the cockpit. To attach the cable to the valve handle ...

Piecing together a historic fuel injection system has proven to be far from easy. I have a bunch of pumps, including three McGee pumps. I really, really wanted to use a McGee pump with the McGee injector. Of the three pumps, only one is salvageable. That's a pretty low hit rate for pumps that were n...