Hey - anyone know any places to get a wheel alignment done on an EK Holden. Prefer in the north western suburbs of Sydney (Ryde area or close by especially good).
John
Search found 34 matches
- Tue May 15, 2007 9:50 pm
- Forum: Suspension and Steering
- Topic: Wheel Alignment Specialist in Sydney
- Replies: 2
- Views: 1271
- Sat Mar 17, 2007 4:51 pm
- Forum: Suspension and Steering
- Topic: Re-installing front springs - help!
- Replies: 3
- Views: 1089
All done
Thanks guys - all done!
- Sat Mar 17, 2007 10:59 am
- Forum: Suspension and Steering
- Topic: Re-installing front springs - help!
- Replies: 3
- Views: 1089
Re-installing front springs - help!
Hi - am at the point where I'm installing some new front springs. Front cross member is attached to the car, but it seems as I jack the car high enough to be able to get the spring in the, the lower control arm is then at too much of a vertical angle to get the spring to sit in the correct place, so...
- Sat Mar 03, 2007 2:56 pm
- Forum: General sharing advice and experience
- Topic: Oil bath air cleaner FB - option?
- Replies: 1
- Views: 680
Oil bath air cleaner FB - option?
Hi - was the oil bath air cleaner an option for the FB?
John
John
- Sat Feb 24, 2007 6:36 pm
- Forum: Suspension and Steering
- Topic: How to safely replace springs when front suspension unit out
- Replies: 13
- Views: 4602
How to safely replace springs when front suspension unit out
Have the front end off my FB, and am restoring it with new rubbers, bushes etc. Also want to replace the shock absorbers and springs. Is there a safe way to do this with it out of the car, as the service manual suggests using jacks to slowly uncompress and recompress the springs. This is of course w...
- Mon Feb 12, 2007 8:47 pm
- Forum: General sharing advice and experience
- Topic: Automatic EK
- Replies: 6
- Views: 1156
EK Hydramatic
It took some time, and had to make some parts, as I don't think there's any Hydramatic parts for EK Holdens around in terms of the linkages. I also found some second hand parts that were in much better condition than mine. Despite all the bad press, the Hydramatic I find works really well. Very smoo...
- Mon Feb 12, 2007 9:10 am
- Forum: General sharing advice and experience
- Topic: Frame rust repairs
- Replies: 8
- Views: 1399
Frame repair
Hey - so not ever having done welding before, is this something most panelbeaters could do? Or is there anyone in the Sydney area someone could suggest? Am in the Ryde area.
John
John
- Mon Feb 12, 2007 9:09 am
- Forum: General sharing advice and experience
- Topic: Automatic EK
- Replies: 6
- Views: 1156
Finding gears
Hey - do you mean it's hard to select a gear using the lever, or the box doesn't seem to shift into gear when it should? If it's trouble with the lever, this is usually caused by worn linkages (there's lots of them). I took all the linkages out of mine, and rebushed them where necessary, and it went...
- Sun Feb 11, 2007 5:58 pm
- Forum: General sharing advice and experience
- Topic: Frame rust repairs
- Replies: 8
- Views: 1399
Frame rust repairs
Hey - what's the best method to repair some not too large rust holes in the box frame section at the front of an FB?
John
John
- Sat Feb 03, 2007 6:40 pm
- Forum: General sharing advice and experience
- Topic: Routing of FB vacuum wiper control cable
- Replies: 2
- Views: 725
Wiper cable
Hey - thanks, that would be great. Yes Chevy is all NSW registered, and currently in use as my daily use car!
J
J
- Fri Feb 02, 2007 8:24 pm
- Forum: General sharing advice and experience
- Topic: Routing of FB vacuum wiper control cable
- Replies: 2
- Views: 725
Routing of FB vacuum wiper control cable
Hi - am putting back a vacuum wiper motor into an FB that had been converted to electric. Just wondering if anyone can tell me how the control cable from the switch is routed to the control slider on the motor?
Thanks,
John
Thanks,
John
- Sat Jan 27, 2007 9:57 am
- Forum: General sharing advice and experience
- Topic: Where to buy vacuum line/flare fittings
- Replies: 1
- Views: 693
Where to buy vacuum line/flare fittings
Hey - just wondering if anyone knows where to buy vacuum line (steel tubing), and flare fittings. Am changing my FB back to vacuum wipers, and will need to make the steel vacuum lines. Also does anyone know what the original diameter of these are? Or to save me the trouble, does anyone have a spare ...
- Fri Jan 26, 2007 12:02 pm
- Forum: General sharing advice and experience
- Topic: Vacuum wiper motor rebuild kit?
- Replies: 1
- Views: 612
Vacuum wiper motor rebuild kit?
Hi - anyone know where to get a rebuild kit for the FB wiper motor?
Anywhere in the US maybe?
John
Anywhere in the US maybe?
John
- Thu Aug 03, 2006 3:34 pm
- Forum: General sharing advice and experience
- Topic: Where to get wheel cylinders for EK
- Replies: 5
- Views: 970
Location and some more info
Sorry, I'm in Sydney, Ryde area. One more question - does anyone know if the EH front left wheel cylinder is the same as on the EK?
- Thu Aug 03, 2006 10:20 am
- Forum: General sharing advice and experience
- Topic: Where to get wheel cylinders for EK
- Replies: 5
- Views: 970
Where to get wheel cylinders for EK
Does anyone know if these are available from say, Repco? Am looking specifically for the front LH one. If yes, anyone have a part number? If no, any suggestions as to where I can find one?
Thanks,
John
Thanks,
John